Why do you want to install things in different places? That sounds overly complicated.
On 11/27/2017 07:03 PM, nan...@luis.uni-hannover.de wrote: > > I am aware of the command line options. However, one needs to keep in > mind where should the particular softeare be installed. Simplest would > be to put that info inside *.eb. > > Quoting Kenneth Hoste <kenneth.ho...@ugent.be>: > >> Hi Gizo, >> >> On 27/11/2017 17:50, nan...@luis.uni-hannover.de wrote: >>> Thank you for your answers. >>> >>> >>>> Gizo: what specific configuration setting would you like to specify in >>>> an easyconfig file, what's your use case? >>> I need to install software on a different location. For this usually >>> I reset easybuild env variables. >>> However, it would be good if as an option I could provide this info >>> in an easyconfig file. >>> What would be other preferred setting for such cases? >> >> You don't need to unset or redefine the environment variables for >> this, you can use the --prefix or --installpath command line option >> (which wins over $EASYBUILD_PREFIX & $EASYBUILD_INSTALLPATH, resp). >> >> Try playing around with "eb --show-config" in a session where >> $EASYBUILD_INSTALLPATH is set, with and without using >> "--installpath=/tmp" as additional option. >> >> See also >> http://easybuild.readthedocs.io/en/latest/Configuration.html#overview-of-current-configuration-show-config-show-full-config >> >> >> regards, >> >> Kenneth >>> >>> Best regards, >>> Gizo >>> >>>> >>>> regards, >>>> >>>> Kenneth >>>> >>>>> regards, >>>>> Pablo. >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> 2017-11-27 14:56 GMT+01:00 nan...@luis.uni-hannover.de >>>>> <mailto:nan...@luis.uni-hannover.de> <nan...@luis.uni-hannover.de >>>>> <mailto:nan...@luis.uni-hannover.de>>: >>>>> >>>>> >>>>> I guess the question was a bit misleading. I meant if one could >>>>> have those config variables in *.eb file >>>>> >>>>> Best regards, >>>>> Gizo >>>>> >>>>> >>>>> On Monday, November 27, 2017 12:59 CET, >>>>> nan...@luis.uni-hannover.de <mailto:nan...@luis.uni-hannover.de> >>>>> <nan...@luis.uni-hannover.de <mailto:nan...@luis.uni-hannover.de>> >>>>> wrote: >>>>> >>>>> > >>>>> > Hello, >>>>> > >>>>> > is there any way to set easybuild env. variables, for example >>>>> the installation path, from within an >>>>> > easybuild config file ? >>>>> > >>>>> > Thank you. >>>>> > >>>>> > best regards, >>>>> > Gizo >>>>> > >>>>> >>>>> >>>>> >>>>> -- >>>>> >>>>> -- >>>>> Dr. Gizo Nanava >>>>> Leibniz Universitaet IT Services >>>>> Leibniz Universitaet Hannover >>>>> Schlosswender Str. 5 >>>>> D-30159 Hannover >>>>> Tel +49 511 762 7919085 <tel:%2B49%20511%20762%207919085> >>>>> http://www.luis.uni-hannover.de <http://www.luis.uni-hannover.de> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> -- >>>>> Pablo Escobar López >>>>> HPC systems engineer >>>>> sciCORE, University of Basel >>>>> SIB Swiss Institute of Bioinformatics >>>>> http://scicore.unibas.ch >>> > > -- Ake Sandgren, HPC2N, Umea University, S-90187 Umea, Sweden Internet: a...@hpc2n.umu.se Phone: +46 90 7866134 Fax: +46 90-580 14 Mobile: +46 70 7716134 WWW: http://www.hpc2n.umu.se