Salut a tous
J'ai installe le usermode-0.4, il tournera 24/24 et je vous vous tiens
au courant.
auparavant, j'avais ajoute qq temps d'attente dans startmodem entre
chaque etape, firmware, modem et ppp
cela evite qq erreurs de chargement avec le module 0.3
en tous cas, n_hdlc est charge automatiquement, je ne sais pas si
c'etait deja le cas
a priori, pas de probleme de charge systeme (kdebug a 1)
rappel de ma config :
RedHat 7.2 standard kernel d'origine
HP Vectra (tres stable ces HP)
PII233/128/6Go
a base de Intel pure
sortie lspci
[root@inetsvr root]# lspci
00:00.0 Host bridge: Intel Corporation 440LX/EX - 82443LX/EX Host bridge
(rev 03)
00:01.0 PCI bridge: Intel Corporation 440LX/EX - 82443LX/EX AGP bridge
(rev 03)
00:04.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 01)
00:04.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
00:04.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
00:04.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 01)
00:06.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
(rev 24)
00:0c.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2164W
[Millennium II]
[r
dmesg
Linux version 2.4.7-10 ([EMAIL PROTECTED]) (gcc
version 2.96
20000731 (Red Hat Linux 7.1 2.96-98)) #1 Thu Sep 6 1
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ebc00 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
Scanning bios EBDA for MXT signature
On node 0 totalpages: 32768
zone(0): 4096 pages.
zone(1): 28672 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda2 BOOT_IMAGE=vmlinuz
Initializing CPU#0
Detected 267.277 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 532.48 BogoMIPS
Memory: 125304k/131072k available (1269k kernel code, 4480k reserved,
90k data,
220k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0080f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0080f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0080f9ff 00000000 00000000 00000000
CPU: Common caps: 0080f9ff 00000000 00000000 00000000
CPU: Intel Pentium II (Klamath) stepping 04
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd9c9, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
mxt_scan_bios: enter
Starting kswapd v1.8
VFS: Diskquotas version dquot_6.5.0 initialized
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
SHARE_IRQ
SERIAL_PCI ISAPNP enabled
Real Time Clock Driver v1.10d
block: queued sectors max/low 83157kB/27719kB, 256 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:DMA, hdb:pio
hda: QUANTUM FIREBALL SE6.4A, ATA DISK drive
hdb: Traxdata CDRW2260+, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 12594960 sectors (6449 MB) w/80KiB Cache, CHS=833/240/63, UDMA(33)
ide-floppy driver 0.97
Partition check:
hda: hda1 hda2 hda3 hda4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
ide-floppy driver 0.97
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 276k freed
VFS: Mounted root (ext2 filesystem).
PCI: Found IRQ 10 for device 00:06.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
00:06.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xfc00. Vers LK1.1.16
Freeing unused kernel memory: 220k freed
Adding Swap: 264592k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.259 $ time 17:36:49 Sep 6 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:04.2
PCI: Sharing IRQ 11 with 00:0c.0
usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.251:USB Universal Host Controller Interface driver
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x547/0x2131) is not claimed by any
active driver.
ide-floppy driver 0.97
hdb: ATAPI 6X CD-ROM CD-R/RW drive, 768kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
cdrom: open failed.
ip_conntrack (1024 buckets, 8192 max)
cdrom: open failed.
PCI: Found IRQ 10 for device 00:06.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
00:06.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xfc00. Vers LK1.1.16
00:06.0: Media override to transceiver type 0 (10baseT).
eth0: Media override to transceiver 0 (10baseT).
usb.c: USB disconnect on device 2
hub.c: USB new device connect on bus1/1, assigned device number 3
usb-uhci.c: interrupt, status 3, frame# 561
usb.c: failed to set device 3 default configuration (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 4
usb.c: USB device 4 (vend/prod 0x915/0x8000) is not claimed by any
active driver.
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.1
cdrom: open failed.
[root@inetsvr root]#
begin:vcard
n:Delacrose;Benoit
tel;cell:33 6 14 66 57 77
tel;home:33 1 69 34 19 34
x-mozilla-html:FALSE
adr:;;;;;;France
version:2.1
email;internet:[EMAIL PROTECTED]
note;quoted-printable:System Engineer on AS/400, Linux and NT. Providing full strategy =0D=0Aand technical consulting services.=0D=0A=0D=0AThe information transmitted is intended only for the person or entity to=0D=0Awhich it is addressed and may contain confidential and/or privileged=0D=0Amaterial. Any review, retransmission, dissemination or other use of, or=0D=0Ataking of any action in reliance upon, this information by persons or=0D=0Aentities other than the intended recipient is prohibited. If you=0D=0Areceived this in error, please contact the sender and delete the material from=0D=0Aany computer.=0D=0A
x-mozilla-cpt:;-1
fn:Benoit Delacrose
end:vcard
