[ECI] FDX310 Modem on SUSE 8.0

Richard Trembecki Fri, 27 Sep 2002 03:18:35 -0700

Hi there,

Im trying to configure a USB FDX310 modem on a standard SUSE 8.0 distribution (based on a 2.4.18 kernel).

Unfortunately I can’t get the ECI driver to load properly.

I can see the modem appearing in the /proc/bus/usb/devices file – listed below

Eci-doctor.sh gives the following result:

You are using linux kernel version 2.4.18-4GB

Support for USB is OK

Preliminary USB device filesystem is OK

UHCI support is OK

/dev/ppp is OK

HDLC support is OK

HDLC support is OK (no bug)

dabusb module is not loaded: OK

I cannot find your ADSL modem: Fatal

Any help would be greatly appreciated

Richard

/proc/bus/usb/devices

I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub

E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0

D: Ver= 1.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1

P: Vendor=0e60 ProdID=0101 Rev= 0.00

C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA

I: If#= 0 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

I: If#= 0 Alt= 1 #EPs=13 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl= 10ms

E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms

E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms

E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms

E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms

E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms

E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms

E: Ad=88(I) Atr=01(Isoc) MxPS= 16 Ivl= 1ms

E: Ad=08(O) Atr=01(Isoc) MxPS= 16 Ivl= 1ms

E: Ad=89(I) Atr=01(Isoc) MxPS= 16 Ivl= 1ms

E: Ad=09(O) Atr=01(Isoc) MxPS= 16 Ivl= 1ms

E: Ad=8a(I) Atr=01(Isoc) MxPS= 16 Ivl= 1ms

E: Ad=0a(O) Atr=01(Isoc) MxPS= 16 Ivl= 1ms

I: If#= 0 Alt= 2 #EPs=13 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl= 10ms