bonjour tout le monde,
je viens de demmarer l installation de debian-30r2 2.4.18 en suivant
le tuto d alexis de lattre.
je suis en australie a sydney alors je vais commencer par vous donner
les info pour configurer la connectier de mon isp.
www.ozforces.com.au
BASIC SETTINGS (Router setup)
Below are the Basic settings to enable your connection if using a Router.
Please note different modems may use different names/titles for settings.
Service name: ozforces (NOTE: no spaces or white space)
User Name: mon numero de tel.your-dsl.net
Password: *********
Disconnect timeout: Zero
Mode/Wan Connection Type: PPPoE LLC (preferred) or PPPoA
Authentication: Auto (CHAP)
DHCP Daemon Client: Disabled/Enabled (User Preference)
VPI: 8
VCI: 35
Operating Mode: Auto or G.DMT
Static IP Address: 0.0.0.0 (Auto)
Subnet Mask: 255.255.255.0
Default Gateway: 0.0.0.0
Bridge mode: Disabled
en cherchant j ai trouve ca :
Primary DNS: 203.194.27.57
Secondary DNS: 203.194.56.150
mais je ne pense pas que ce soit necessaire.
ensuite,
==== Configuration will be created with these values :
+ User : [email]"myphonenumber"@dcd1.your-dsl.net[/email]
+ Password : (hidden)
+ Provider : Other
DNS 1 :
DNS 2 :
+ VPI/VCI : 8/35
+ Modem : Other
VID1/PID1 : 0547/2131
VID2/PID2 : 0915/8000
+ .bin file : /etc/eciadsl/synch01.bin
+ PPP mode : LLC_RFC2364
+ use DHCP : no
+ use static IP : no
j ai lu sur votre site que le site sync01 et 03 etait bon pour l
australie mais j e n ai pas tester le 03.
startmodem
et la:
setting up USB support (1/5)..
loading firmware (2/5)..
firmware seems to be already loaded
setting up modem (3/5)..
ECI load 2: success
synchronization successful
connecting modem (4/5)..
using channel 2
Using interface ppp0
Connect: ppp0 <--> /dev/pts/1
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x164ece33>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x164ece33>]
rcvd [LCP ConfReq id=0xe4 <auth chap MD5> <magic 0x272f2fa9>]
sent [LCP ConfAck id=0xe4 <auth chap MD5> <magic 0x272f2fa9>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x164ece33>]
rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x164ece33>]
rcvd [CHAP Challenge id=0x34 <596e75d20e5b003b6fea82a8ea9602fa>, name =
"ncb1-chatswood"]
sent [CHAP Response id=0x34 <f412d89a63ab4a37ae1915eabbb90bf5>, name = ""my phine
number"@dcd1.your-dsl.net"]
rcvd [LCP ConfReq id=0x2 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfReq id=0x2 <asyncmap 0x0> <magic 0x7962718c>]
sent [LCP ConfAck id=0x2 <auth chap MD5> <magic 0xd91f626>]
rcvd [LCP ConfReq id=0x3 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfAck id=0x3 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfReq id=0x2 <asyncmap 0x0> <magic 0x7962718c>]
rcvd [LCP ConfReq id=0x4 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfAck id=0x4 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfReq id=0x2 <asyncmap 0x0> <magic 0x7962718c>]
rcvd [LCP ConfReq id=0x5 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfAck id=0x5 <auth chap MD5> <magic 0xd91f626>]
rcvd [LCP ConfReq id=0x6 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfAck id=0x6 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfReq id=0x2 <asyncmap 0x0> <magic 0x7962718c>]
rcvd [LCP ConfReq id=0x7 <auth chap MD5> <magic 0xd91f626>]
sent [LCP ConfAck id=0x7 <auth chap MD5> <magic 0xd91f626>]
qu est ce que je dois faire ?
merci et bravo pour votre boulot.
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Driver Linux pour modem ECI ADSL USB: http://eciadsl.flashtux.org
Archives de cette liste de diffusion: http://liste.eci.free.fr
Pour se desinscrire: mailto:[EMAIL PROTECTED]
