Cc: Michael D Kinney <michael.d.kin...@intel.com>
Cc: Liming Gao <liming....@intel.com>
Cc: Feng Tian <feng.t...@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.z...@intel.com>
Reviewed-by: Liming Gao <liming....@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kin...@intel.com>
---
.../BaseSerialPortLib16550.c | 347 +++++++++++++++++++++
1 file changed, 347 insertions(+)
diff --git
a/MdeModulePkg/Library/BaseSerialPortLib16550/BaseSerialPortLib16550.c
b/MdeModulePkg/Library/BaseSerialPortLib16550/BaseSerialPortLib16550.c
index 5b6608d..fcc289c 100644
--- a/MdeModulePkg/Library/BaseSerialPortLib16550/BaseSerialPortLib16550.c
+++ b/MdeModulePkg/Library/BaseSerialPortLib16550/BaseSerialPortLib16550.c
@@ -40,7 +40,9 @@
#define R_UART_LCR 3
#define B_UART_LCR_DLAB BIT7
#define R_UART_MCR 4
+#define B_UART_MCR_DTRC BIT0
#define B_UART_MCR_RTS BIT1
+#define B_UART_MCR_LME BIT4
#define R_UART_LSR 5
#define B_UART_LSR_RXRDY BIT0
#define B_UART_LSR_TXRDY BIT5
@@ -48,6 +50,8 @@
#define R_UART_MSR 6
#define B_UART_MSR_CTS BIT4
#define B_UART_MSR_DSR BIT5
+#define B_UART_MSR_RI BIT6
+#define B_UART_MSR_DCD BIT7
//
// 4-byte structure for each PCI node in PcdSerialPciDeviceInfo
@@ -761,3 +765,346 @@ SerialPortPoll (
return FALSE;
}
+
+/**
+ Sets the control bits on a serial device.
+
+ @param Control Sets the bits of Control that are settable.
+
+ @retval RETURN_SUCCESS The new control bits were set on the serial
device.
+ @retval RETURN_UNSUPPORTED The serial device does not support this
operation.
+ @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
+
+**/
+RETURN_STATUS
+EFIAPI
+SerialPortSetControl (
+ IN UINT32 Control
+ )
+{
+ UINTN SerialRegisterBase;
+ UINT8 Mcr;
+
+ //
+ // First determine the parameter is invalid.
+ //
+ if ((Control & (~(EFI_SERIAL_REQUEST_TO_SEND |
EFI_SERIAL_DATA_TERMINAL_READY |
+ EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE |
EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE |
+ EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE))) != 0) {
+ return RETURN_UNSUPPORTED;
+ }
+
+ SerialRegisterBase = GetSerialRegisterBase ();
+ if (SerialRegisterBase ==0) {
+ return RETURN_UNSUPPORTED;
+ }
+
+ //
+ // Read the Modem Control Register.
+ //
+ Mcr = SerialPortReadRegister (SerialRegisterBase, R_UART_MCR);
+ Mcr &= (~(B_UART_MCR_DTRC | B_UART_MCR_RTS | B_UART_MCR_LME));
+
+ if ((Control & EFI_SERIAL_DATA_TERMINAL_READY) ==
EFI_SERIAL_DATA_TERMINAL_READY) {
+ Mcr |= B_UART_MCR_DTRC;
+ }
+
+ if ((Control & EFI_SERIAL_REQUEST_TO_SEND) == EFI_SERIAL_REQUEST_TO_SEND) {
+ Mcr |= B_UART_MCR_RTS;
+ }
+
+ if ((Control & EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE) ==
EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE) {
+ Mcr |= B_UART_MCR_LME;
+ }
+
+ //
+ // Write the Modem Control Register.
+ //
+ SerialPortWriteRegister (SerialRegisterBase, R_UART_MCR, Mcr);
+
+ return RETURN_SUCCESS;
+}
+
+/**
+ Retrieve the status of the control bits on a serial device.
+
+ @param Control A pointer to return the current control
signals from the serial device.
+
+ @retval RETURN_SUCCESS The control bits were read from the serial
device.
+ @retval RETURN_UNSUPPORTED The serial device does not support this
operation.
+ @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
+
+**/
+RETURN_STATUS
+EFIAPI
+SerialPortGetControl (
+ OUT UINT32 *Control
+ )
+{
+ UINTN SerialRegisterBase;
+ UINT8 Msr;
+ UINT8 Mcr;
+ UINT8 Lsr;
+
+ SerialRegisterBase = GetSerialRegisterBase ();
+ if (SerialRegisterBase ==0) {
+ return RETURN_UNSUPPORTED;
+ }
+
+ *Control = 0;
+
+ //
+ // Read the Modem Status Register.
+ //
+ Msr = SerialPortReadRegister (SerialRegisterBase, R_UART_MSR);
+
+ if ((Msr & B_UART_MSR_CTS) == B_UART_MSR_CTS) {
+ *Control |= EFI_SERIAL_CLEAR_TO_SEND;
+ }
+
+ if ((Msr & B_UART_MSR_DSR) == B_UART_MSR_DSR) {
+ *Control |= EFI_SERIAL_DATA_SET_READY;
+ }
+
+ if ((Msr & B_UART_MSR_RI) == B_UART_MSR_RI) {
+ *Control |= EFI_SERIAL_RING_INDICATE;
+ }
+
+ if ((Msr & B_UART_MSR_DCD) == B_UART_MSR_DCD) {
+ *Control |= EFI_SERIAL_CARRIER_DETECT;
+ }
+
+ //
+ // Read the Modem Control Register.
+ //
+ Mcr = SerialPortReadRegister (SerialRegisterBase, R_UART_MCR);
+
+ if ((Mcr & B_UART_MCR_DTRC) == B_UART_MCR_DTRC) {
+ *Control |= EFI_SERIAL_DATA_TERMINAL_READY;
+ }
+
+ if ((Mcr & B_UART_MCR_RTS) == B_UART_MCR_RTS) {
+ *Control |= EFI_SERIAL_REQUEST_TO_SEND;
+ }
+
+ if ((Mcr & B_UART_MCR_LME) == B_UART_MCR_LME) {
+ *Control |= EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE;
+ }
+
+ if (PcdGetBool (PcdSerialUseHardwareFlowControl)) {
+ *Control |= EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE;
+ }
+
+ //
+ // Read the Line Status Register.
+ //
+ Lsr = SerialPortReadRegister (SerialRegisterBase, R_UART_LSR);
+
+ if ((Lsr & (B_UART_LSR_TEMT | B_UART_LSR_TXRDY)) == (B_UART_LSR_TEMT |
B_UART_LSR_TXRDY)) {
+ *Control |= EFI_SERIAL_OUTPUT_BUFFER_EMPTY;
+ }
+
+ if ((Lsr & B_UART_LSR_RXRDY) == 0) {
+ *Control |= EFI_SERIAL_INPUT_BUFFER_EMPTY;
+ }
+
+ return RETURN_SUCCESS;
+}
+
+/**
+ Sets the baud rate, receive FIFO depth, transmit/receice time out, parity,
+ data bits, and stop bits on a serial device.
+
+ @param BaudRate The requested baud rate. A BaudRate value of 0
will use the
+ device's default interface speed.
+ On output, the value actually set.
+ @param ReveiveFifoDepth The requested depth of the FIFO on the receive
side of the
+ serial interface. A ReceiveFifoDepth value of 0
will use
+ the device's default FIFO depth.
+ On output, the value actually set.
+ @param Timeout The requested time out for a single character in
microseconds.
+ This timeout applies to both the transmit and
receive side of the
+ interface. A Timeout value of 0 will use the
device's default time
+ out value.
+ On output, the value actually set.
+ @param Parity The type of parity to use on this serial device. A
Parity value of
+ DefaultParity will use the device's default parity
value.
+ On output, the value actually set.
+ @param DataBits The number of data bits to use on the serial
device. A DataBits
+ vaule of 0 will use the device's default data bit
setting.
+ On output, the value actually set.
+ @param StopBits The number of stop bits to use on this serial
device. A StopBits
+ value of DefaultStopBits will use the device's
default number of
+ stop bits.
+ On output, the value actually set.
+
+ @retval RETURN_SUCCESS The new attributes were set on the serial
device.
+ @retval RETURN_UNSUPPORTED The serial device does not support this
operation.
+ @retval RETURN_INVALID_PARAMETER One or more of the attributes has an
unsupported value.
+ @retval RETURN_DEVICE_ERROR The serial device is not functioning
correctly.
+
+**/
+RETURN_STATUS
+EFIAPI
+SerialPortSetAttributes (
+ IN OUT UINT64 *BaudRate,
+ IN OUT UINT32 *ReceiveFifoDepth,
+ IN OUT UINT32 *Timeout,
+ IN OUT EFI_PARITY_TYPE *Parity,
+ IN OUT UINT8 *DataBits,
+ IN OUT EFI_STOP_BITS_TYPE *StopBits
+ )
+{
+ UINTN SerialRegisterBase;
+ UINT32 SerialBaudRate;
+ UINTN Divisor;
+ UINT8 Lcr;
+ UINT8 LcrData;
+ UINT8 LcrParity;
+ UINT8 LcrStop;
+
+ SerialRegisterBase = GetSerialRegisterBase ();
+ if (SerialRegisterBase ==0) {
+ return RETURN_UNSUPPORTED;
+ }
+
+ //
+ // Check for default settings and fill in actual values.
+ //
+ if (*BaudRate == 0) {
+ *BaudRate = PcdGet32 (PcdSerialBaudRate);
+ }
+ SerialBaudRate = (UINT32) *BaudRate;
+
+ if (*DataBits == 0) {
+ LcrData = (UINT8) (PcdGet8 (PcdSerialLineControl) & 0x3);
+ *DataBits = LcrData + 5;
+ } else {
+ if ((*DataBits < 5) || (*DataBits > 8)) {
+ return RETURN_INVALID_PARAMETER;
+ }
+ //
+ // Map 5..8 to 0..3
+ //
+ LcrData = (UINT8) (*DataBits - (UINT8) 5);
+ }
+
+ if (*Parity == DefaultParity) {
+ LcrParity = (UINT8) ((PcdGet8 (PcdSerialLineControl) >> 3) & 0x7);
+ switch (LcrParity) {
+ case 0:
+ *Parity = NoParity;
+ break;
+
+ case 3:
+ *Parity = EvenParity;
+ break;
+
+ case 1:
+ *Parity = OddParity;
+ break;
+
+ case 7:
+ *Parity = SpaceParity;
+ break;
+
+ case 5:
+ *Parity = MarkParity;
+ break;
+
+ default:
+ break;
+ }
+ } else {
+ if ((*Parity < NoParity) || (*Parity > SpaceParity)) {
+ return RETURN_INVALID_PARAMETER;
+ }
+ switch (*Parity) {
+ case NoParity:
+ LcrParity = 0;
+ break;
+
+ case EvenParity:
+ LcrParity = 3;
+ break;
+
+ case OddParity:
+ LcrParity = 1;
+ break;
+
+ case SpaceParity:
+ LcrParity = 7;
+ break;
+
+ case MarkParity:
+ LcrParity = 5;
+ break;
+
+ default:
+ break;
+ }
+ }
+
+ if (*StopBits == DefaultStopBits) {
+ LcrStop = (UINT8) ((PcdGet8 (PcdSerialLineControl) >> 2) & 0x1);
+ switch (LcrStop) {
+ case 0:
+ *StopBits = OneStopBit;
+ break;
+
+ case 1:
+ if (*DataBits == 5) {
+ *StopBits = OneFiveStopBits;
+ } else {
+ *StopBits = TwoStopBits;
+ }
+ break;
+
+ default:
+ break;
+ }
+ } else {
+ if ((*StopBits < OneStopBit) || (*StopBits > TwoStopBits)) {
+ return RETURN_INVALID_PARAMETER;
+ }
+ switch (*StopBits) {
+ case OneStopBit:
+ LcrStop = 0;
+ break;
+
+ case OneFiveStopBits:
+ case TwoStopBits:
+ LcrStop = 1;
+ break;
+
+ default:
+ break;
+ }
+ }
+
+ //
+ // Calculate divisor for baud generator
+ // Ref_Clk_Rate / Baud_Rate / 16
+ //
+ Divisor = PcdGet32 (PcdSerialClockRate) / (SerialBaudRate * 16);
+ if ((PcdGet32 (PcdSerialClockRate) % (SerialBaudRate * 16)) >=
SerialBaudRate * 8) {
+ Divisor++;
+ }
+
+ //
+ // Configure baud rate
+ //
+ SerialPortWriteRegister (SerialRegisterBase, R_UART_LCR, B_UART_LCR_DLAB);
+ SerialPortWriteRegister (SerialRegisterBase, R_UART_BAUD_HIGH, (UINT8)
(Divisor >> 8));
+ SerialPortWriteRegister (SerialRegisterBase, R_UART_BAUD_LOW, (UINT8)
(Divisor & 0xff));
+
+ //
+ // Clear DLAB and configure Data Bits, Parity, and Stop Bits.
+ // Strip reserved bits from line control value
+ //
+ Lcr = (UINT8) ((LcrParity << 3) | (LcrStop << 2) | LcrData);
+ SerialPortWriteRegister (SerialRegisterBase, R_UART_LCR, (UINT8) (Lcr &
0x3F));
+
+ return RETURN_SUCCESS;
+}
+
--
1.9.5.msysgit.0
_______________________________________________
edk2-devel mailing list
edk2-devel@lists.01.org
https://lists.01.org/mailman/listinfo/edk2-devel
