DebugAgentDxe will consume Serial Port to setup debug channel with HOST. Please shutdown the UDK debug HOST software and use any serial tool (Like putty). Are there any output when you load DebugAgentDxe in shell? Could you paste here?
You need to make sure the DebugAgentDxe used the correct serial port parameter on your platform. Thanks! Jeff -----Original Message----- From: Arka Sharma [mailto:arka.sw1...@gmail.com] Sent: Friday, March 31, 2017 9:40 AM To: Kinney, Michael D Cc: Fan, Jeff; edk2-devel@lists.01.org Subject: Re: [edk2] Using Intel UDk debugger Thanks a lot Mike. You are right. I have installed WinDbg 6.11.1404. Now the issue I mentioned earlier is not seen. But I am still not able to break into target system. I have loaded the DebugAgentDxe and loading was success. But in the shell I can find that still the serial port handle is not managed by any driver. Regards, Arka On Thu, Mar 30, 2017 at 9:28 PM, Kinney, Michael D <michael.d.kin...@intel.com> wrote: > Hi Arka, > > I have seen that error when the wrong version of WinDbg is used. > > What version of WinDbg did you install? > > Does it match the version listed in the UDK Debugger manual? > > Mike > >> -----Original Message----- >> From: edk2-devel [mailto:edk2-devel-boun...@lists.01.org] On Behalf >> Of Arka Sharma >> Sent: Thursday, March 30, 2017 2:43 AM >> To: Fan, Jeff <jeff....@intel.com> >> Cc: edk2-devel@lists.01.org >> Subject: Re: [edk2] Using Intel UDk debugger >> >> I have also verified the null modem connection by booting to windows >> in my target pc, and I am able to break it in WinDbg. So the >> communication is ok. In the target system shell when I load the >> DebugAgentDxe it is not appeared in the "drivers -b". Also in my >> system the serial port is not managed by any driver initially. So I >> located it using "devices" and the issued "load -nc >> DebugAgentDxe.efi". >> >> Regards, >> Arka >> >> On Thu, Mar 30, 2017 at 2:27 PM, Arka Sharma <arka.sw1...@gmail.com> wrote: >> > Thanks Jeff for your reply. I followed the steps as mentioned in >> > "9.11 Debugging a standalone module loaded in a UEFI shell". I have >> > built DebugAgentDxe and loaded it in my target system. I cross >> > checked in my target system UEFI setup Serial is enabled. In host I >> > have installed >> > WinDbgX64 and UDK debugger. I have configured the debug port COM1, >> > connected the host and target with a null modem cable. Now when I >> > launch SoftDebugger WinDbg starts with an error message "Could not >> > start kernel debugging using >> > exdi:clsid={F56FC1A6-3422-4320-A7F3-41EAEC2A367D} parameters. If I >> > attempt to reconnect with COM1 it throws "Access denied". Do I need >> > to enable something more in target system ? >> > >> > Regards, >> > Arka >> > >> > On Thu, Mar 30, 2017 at 10:55 AM, Fan, Jeff <jeff....@intel.com> wrote: >> >> Arka, >> >> >> >> UDK Debugger tool supports your usage model. >> >> >> >> Please see the section "9.11 Debugging a standalone module loaded >> >> in a UEFI >> shell" @ >> https://firmware.intel.com/sites/default/files/UDK_Debugger_Tool_User_Manual_V1.11. >> pdf >> >> >> >> Thanks! >> >> Jeff >> >> -----Original Message----- >> >> From: edk2-devel [mailto:edk2-devel-boun...@lists.01.org] On >> >> Behalf Of Arka >> Sharma >> >> Sent: Thursday, March 30, 2017 1:15 PM >> >> To: edk2-devel@lists.01.org >> >> Subject: [edk2] Using Intel UDk debugger >> >> >> >> Hi, >> >> >> >> I am sorry if it is not a right place to ask this. I have >> >> installed WinDbg and >> Intel UDK debugger. I want to debug a driver and an application on an >> Asrock borad, but going through the UDK debugger user manual I >> realize that SourceLevelDebugPkg has to be included in target >> firmware image. Now in this case what option do I have to proceed >> with the debugging ? I am launching my application from shell and in >> the shell post codes are disabled, the application code get stuck >> randomly. So far I was trying to debug with AsciiPrints. Is there any >> way to use DEBUG macro to redirect debug messages from UEFI driver as well >> as application to some serial port in this case ? >> >> >> >> Regards, >> >> Arka >> >> _______________________________________________ >> >> edk2-devel mailing list >> >> edk2-devel@lists.01.org >> >> https://lists.01.org/mailman/listinfo/edk2-devel >> _______________________________________________ >> edk2-devel mailing list >> edk2-devel@lists.01.org >> https://lists.01.org/mailman/listinfo/edk2-devel _______________________________________________ edk2-devel mailing list edk2-devel@lists.01.org https://lists.01.org/mailman/listinfo/edk2-devel
