I have a gigabyte b360n-wifi board with 2 onboard eth cards. it is a mini
itx board in a tiny little case so a pci card is not a feasible option for
fixing this problem. one of the cards is detected on install, the other is
not. i'm looking for any help in adding drivers for the second card (i have
not done anything like this in 15 years back when you had to build your own
wifi drivers in linux. and even then i had apt at my disposal-- i've never
attempted any of this without a repos)
below is relevant lspci output. the card at 01:00.0 is the working card.
the 00:1f.6 is the one that is not coming up
00:1f.6 Ethernet controller: Intel Corporation Device 15bc (rev 10)
Subsystem: Gigabyte Technology Co., Ltd Device e000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at a1200000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
01:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network
Connection (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device e000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at a1100000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 3000 [size=32]
Region 3: Memory at a1120000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
FLReset-
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <2us, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-,
OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Kernel driver in use: igb
Kernel modules: igb
root@efw-95b8305614:~ # lspci -vv | grep Ethernet
00:1f.6 Ethernet controller: Intel Corporation Device 15bc (rev 10)
01:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network
Connection (rev 03)
any help would be greatly appreciated
_______________________________________________
Efw-user mailing list
Efw-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/efw-user
