Hi Wolf, Thanks for the detailed explanation. I've found the bug and it will be fixed in the next firmware revision. It turns out that the Center Frequency adjustment also was not working properly above 200 MHz.
> Sorry about being not clear enough, but my English is too poor to make > the explanation clearer. Hope you understand my problem anyway ;-). Danke sehr fur schreiben auf englisch. Mein deutsch ist nicht sehr gut! Alan N1AL On Thu, 2010-09-16 at 18:26 +0200, Wolf E. Rose wrote: > hi Jim, > > sorry I've been not clear enough to explain my problem. > > It is the CENTER frequency I'm talking about not the SPAN. > > For example: receiving frequency is at 432.418 MHz (German beacon) and > P3 has been switched on together with K3. P3 displays the same center > frequency as the K3 dial shows. Now you tap 'Marker A' an switch it > on. Displayed on P3's screen is 'Marker A 432418'. As soon as you dial > the P3 select the P3's display shows 'Marker A 200000'. You only can > now dial to a frequency BELOW 200000, there's no chance dialing mor > than 200000. > > If you now try qsying via P3 selct (tap to QSY) the K3 won't follow. > It is fixed to K3's frequency. > > Sorry about being not clear enough, but my English is too poor to make > the explanation clearer. Hope you understand my problem anyway ;-). > > Thanks for answering es 73 > Wolf DK1IP > > > Am 16.09.2010 um 14:21:01 schrieb Jim Cox: > > > The span of the P3 is 200 khz. You state 200 mhz so not sure if > > span is what your questioning. > > > > Jim K4JAF > > > > > > ----- Original Message ----- From: "Wolf E. Rose" <wolf.e.r...@freenet.de > > > > > To: <elecraft@mailman.qth.net> > > Sent: Thursday, September 16, 2010 12:47 AM > > Subject: [Elecraft] P3 cursors won't go up more then 200 MHz > > > > > >> hi folks, > >> > >> just preparing everything for the IARU-region 1 UHF/SHF-contest > >> (10/2-3). > >> > >> While testing I was not able to set the P3's cursors beyond 200 MHz. > >> Anybody show me the right way to exceed this frequency limit please. > >> I'm sure this must be a software bug between operator's ears. > >> Everything else (K3/10 #1935, Kuhne TR432H transverter) working > >> together fine since years. Only the brandnew P3 #323 won't > >> follow ... ;-( > >> > >> 73 > >> Wolf DK1IP > >> ______________________________________________________________ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:Elecraft@mailman.qth.net > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: http://www.qsl.net/donate.html > > > > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
