Thanks for the suggestions. I figured out the PTT issue by disconnecting the PTT from the signalink. Then allowing the software to control the PTT and it now operates properly and does not hang. Now to tackle the audio problem. I have checked that it in is Data A and that it is set to line input, I have the monitor on and still nothing no matter where the levels are set. I see no output and hear nothing from the monitoring. If it was not receiving I would wonder if I had the line in and line out cables mixed up. My next plan is to check the cable from the signalink and make sure that there is audio coming out of the cable. Brney
-------- Original Message -------- Subject: Re: Two issues with data transmission From: "Richard Ferch [via Elecraft]" < [email protected] > Date: Sun, April 24, 2011 11:10 am To: cbscholl < [email protected] > Barney, Re the first problem, I suspect your LINE IN level may be sitting on zero. With the radio in DATA A or AFSK A mode, make sure your MIC SEL is set to LINE IN (I believe this is the default in DATA A and AFSK A modes, but if not you can set it using the MENU button). Now turning the MIC gain control will adjust the LINE IN level. You should set the meter to display ALC and then adjust the LINE IN level (and/or the SignaLink's output level) until you see 4-5 bars of "ALC" reading on the K3. Use the PWR control to select the desired output power. In modes that require high linearity, like PSK, stay below one-half the radio's power rating (i.e. between 12 and 50 watts or below 5 watts) to avoid clipping on momentary peaks. R e the second problem, is your SignaLink connected to the radio's PTT input? If it is, you should make sure that your software is *not* configured to control PTT. In particular, make sure that it is not using software commands for PTT. Also, you should turn the radio's VOX off. The SignaLink has its own VOX circuit that controls PTT for you. There is no need for an additional PTT method, and in fact using two methods simultaneously can cause this problem. The K3 appears to be vulnerable to a "race condition", in which sending a software RX command simultaneously with switching hardware PTT (or the radio's VOX) can leave the radio in transmit. 73, Rich VE3KI K3LA wrote: > I recently tried to set up my K3 for data usage and two problems arose. I am > using a signalink interface. I have tried to use both FLDIGI and HRD and the > problems are present in both cases. > First there appears to be audio coming out of the Signalink but no rf output > and I am hearing not hing from the monitor out. > The second problem is that once the transmitter is keyed, by both the > program through the computer and the output from the Signalink and the > trsanmission is stopped the transmitter hangs on transmit. > Any suggestions would be appreciated. ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto: [hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html If you reply to this email, your message will be added to the discussion below: http://elecraft.365791.n2.nabble.com/Two-issues-with-data-transmission-tp6300401p6301089.html To unsubscribe from Two issues with data transmission, click here . -- View this message in context: http://elecraft.365791.n2.nabble.com/Two-issues-with-data-transmission-tp6300401p6301583.html Sent from the Elecraft mailing list archive at Nabble.com. ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
