Did the VCO calibration on the Sub receiver go OK? On 1/26/2012 8:26 PM, Cady, Fred wrote: > Hi Gary, > Sure sounds like the sub receiver is using a different antenna than the > main when on 20 meters. The antenna configuration is kept on a per-band > basis so it could be different on 20 than on the other bands. What I'd > think I'd do is tap A>B twice to make sure all the filters are the same > in each receiver (maybe try some different filter width settings to make > sure something hasn't gone wrong with the sub rx's filter > configuration). Then make sure the sub is using the same antenna as the > main. In B-Set, tap ANT to select ANT1 or ANT2, which ever is being used > by the main. If not in B-Set, holding RX ANT will show MAIN or AUX for > the sub rx. You want MAIN. > That's about all I can think of. > 73 and cheers, > > > Fred KE7X > "The Elecraft K3; Design, Configuration and Operation" > www.ke7x.com > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Gary Smith > Sent: Thursday, January 26, 2012 9:02 PM > To: [email protected] > Subject: Re: [Elecraft] Getting the sub to work on 20M > > I've looked through the manual (PDF version& searched memory and > antenna& sub) and I can't seem to find anything that helps me in this > problem. > > When I go to B Set to configure the sub Rx when I'm on 20M, nothing I do > gets the sub Rx to work regardless of the antenna I'm using. I hear a > loud hiss but nowhere do I get Rf with the sub on 20M. All other bands I > do. > > Anyone have any specific suggestions what I can try to get the sub > working on 20? > > Thanks > > Gary KA1J > > >> 20m probably has the wrong antenna in it's memory >> >> >> GB& 73 >> K5OAI >> Sam Morgan >> >> On 1/26/2012 2:43 PM, Gary Smith wrote: >>> K3& sub Rx installed. >>> >>> I rarely use the Rx antenna on the upper bands but today went to >>> work TN2T on 20 SSB to work split and discovered I don't hear >>> anything Rf wise coming from the sub Rx. I have no problems with the >>> sub hearing independently on the other bands& used it to find the >>> right split on 10M& it works fine on the lower bands, seems like >>> it's confined to 20M. >>> >>> Any ideas if there's anything I can check to see if it's not set up >>> right? >>> >>> Thanks, >>> >>> Gary >>> KA1J >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net Please help support this >>> email list: http://www.qsl.net/donate.html >>> > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected]
This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
