Set "VFO IND" to Yes. 73 de Sebastian, W4AS
On Feb 13, 2012, at 9:37 AM, Jack Berry wrote: > Oli, > Just started using HRD myself and searching for a solution to the same > problem > which I call "bouncing band change". > > For me, when I change frequencies within the same band HRD works as expected. > It's when using HRD Logbook and I click a DX spot in a different band that > the > problem occurs. > I'm sure someone on this reflector has the answer we need. > > I'll let you know if I find the answer today. > > 73, Jack - WE5ST > > > > > ________________________________ > From: "[email protected]" <[email protected]> > To: [email protected] > Sent: Mon, February 13, 2012 6:30:34 AM > Subject: [Elecraft] My new K3 has arrived on Saturday > > 2nd try, first had a html e-mail > > Hello, > my new K3/100F has arrived on Saturday. So I removed my IC-7400 from the > position right to the screen and put it on the left. The IC-7400 is now > my dedicated 6m an 2m SSB/CW radio. On the right sits the K3 now. > Please have a look: http://files.qrz.com/i/dl1oli/dl1oli_K3_k.jpg > > I already had a Ftdi USB-seriell interface and now use this for control > of the K3. I made all of the connections to the PC, Amp, antennas ect. I > even had made cable with the right 3.5 mm connectors (stereo for > speaker/line-out and mono for line/mic in). > I configured Ham-Radio-Deluxe 5 for the K3. > > Now I have two problems: > 1. If I use the DX-cluster in HRD Logbook an click on an dx-entry which > is not on the same band where the K3 is, then the K3 changes to the new > frequency, an directly after it goes back to the old frequency. For > example. The K3 is on 14300 kHz, in the HRD-Logbook dx-cluster is an > entry for 21400 kHz. Then the K3 changes shortly to 21400 and > immediately goes back to 14300. ? > > 2. The rear line-in does not work. I connected my sound-card to the > line-in with an 3.5 mm mono connector on the radio-end. I used the MAIN > menu to change the source to line in. But tthen it does not modulate on > TX. If I connect the same cable from the sound-card in the rear > microphone instead of line-in, then the K3 modulates. I tried USB and > DATA A modes. The Sound-card and cable is OK because it works in the > rear-mic. ? > > I made some contacts in the CQ WPX-RTTY contest on the weekend. I used > HRD and DM780 for casual contesting. So far it works nicely. I have a > 250 Hz Filter installed and this is very good for strong nearby > RTTY-stations on 40 m. I configured the 250 Hz Filter as a 300 Hz. > > Do you have hints or solutions for my two problems? > > 73 Oli > DL1OLI/AJ4UR > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
