> Can someone please give me a list of dial display frequencies
> used with a K3 for USB and CW on 60 Meters, all five Channels?

The following table shows which modes may be used on which frequencies:

Displayed
Frequency                         Authorized Modes (Emissions)

5330.5 kHz   USB Phone (2K80J3E), USB PSK31 (60H0J2B), USB PACTOR-III (2K80J2D)
5332.0 kHz   CW (150HA1A)

5346.5 kHz   USB Phone (2K80J3E), USB PSK31 (60H0J2B), USB PACTOR-III (2K80J2D)
5348.0 kHz   CW (150HA1A)

5357.0 kHz   USB Phone (2K80J3E), USB PSK31 (60H0J2B), USB PACTOR-III (2K80J2D)
5358.5 kHz   CW (150HA1A)

5371.5 kHz   USB Phone (2K80J3E), USB PSK31 (60H0J2B), USB PACTOR-III (2K80J2D)
5373.0 kHz   CW (150HA1A)

5403.5 kHz   USB Phone (2K80J3E), USB PSK31 (60H0J2B), USB PACTOR-III (2K80J2D)
5405.0 kHz   CW (150HA1A)

I store these ten frequencies shown above in ten memories on my various HF 
rigs, in pairs of two with USB mode stored for the first and CW mode stored for 
the second of each pair.

Background:

The FCC report related to the 05 March 2012 60 meter band rule changes was 
published in the Federal Register at 
http://www.gpo.gov/fdsys/pkg/FR-2012-02-03/pdf/2012-2477.pdf .

It authorizes five 3 kHz channels, each with the following channel CENTER 
frequencies:

5332.0 kHz
5348.0 kHz
5358.5 kHz
5373.0 kHz
5405.0 kHz .

It designates five channel CARRIER frequencies that are 1.5 kHz BELOW the 
channel CENTER frequencies:

5330.5 kHz
5346.5 kHz
5357.0 kHz
5371.5 kHz
5403.5 kHz .

The authorized emissions and frequencies for 60 meters are:

150HA1A  CW Morse telegraphy. 
         Transmitter dial must be set to the channel CENTER frequency.
2K80J3E  USB phone.
         Transmitter dial must be set to the channel CARRIER frequency
         (which is 1.5 kHz BELOW the channel CENTER frequency).
60H0J2B  RTTY (ONLY PSK31, sent on USB phone).
         Transmitter dial must be set to the channel CARRIER frequency
         (which is 1.5 kHz BELOW the channel CENTER frequency).
2K80J2D  DATA (ONLY PACTOR-III, sent on USB phone).
         Transmitter dial must be set to the channel CARRIER frequency
         (which is 1.5 kHz BELOW the channel CENTER frequency).

The applicable 47CFR97 regulations are found at 
http://www.ecfr.gov/cgi-bin/text-idx?c=ecfr&SID=1e17c74c2975ff111a839967ad3f2f38&rgn=div5&view=text&node=47:5.0.1.1.6&idno=47#47:5.0.1.1.6.4.157.2

Most related information is found in sections 97.303 though 97.307 found in the 
above link.

Mike / KK5F

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]

Reply via email to