Check all the coaxial cables that plug into the boards and front panel.
Make sure they go the right places. I would also check the way you have
decided to handle the coax going to the coax chassis connector SO239.
There are a couple of ways to do this depending on your options.
Mike W0MU
On 3/1/2015 3:45 PM, Joe Moffatt wrote:
Ok, checked the RX ANT switch. It was not on. I did connect an antenna to
the RX ANT jack and switched to it, but no difference.
Not sure what is wrong where. In any case, there is very little sensitivity
in the K3 at this point.
Don't know what to check. I have gone back through the best I can... seems
everything was done correctly.
Very careful about ESD.
Joe
From: Wayne Burdick [mailto:[email protected]]
Sent: Sunday, March 1, 2015 12:38 PM
To: Joe Moffatt
Cc: [email protected]
Subject: Re: [Elecraft] New K3 build, LOW LOW sensitivity.
Joe,
Do you have a KXV3 module installed? You may be switched to the RX antenna.
Wayne
N6KR
On Mar 1, 2015, at 7:48 AM, joemoffatt
<[email protected]><mailto:[email protected]%3e> wrote:
Everything in the manual checked out ok. I am at the stage before putting in
the 100 watt PA. Just checking things out. I have the IF Out board, but
that's about it. No ATU. Setup filters, etc. But, I have only about S1
on the S Meter, and can only weakly hear the strongest of signals. Even WWV
is poor. This is on a known good antenna/coax.
Anyhow, just wondering what to check. I haven't set the REF OSC yet because
I can't get a strong enough signal to do it.
Ideas? I thought I was sailing along smoothly.
Thanks,
joe
--
View this message in context:
http://elecraft.365791.n2.nabble.com/New-K3-build-LOW-LOW-sensitivity-tp7599593.html
Sent from the Elecraft mailing list archive at Nabble.com.
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]<mailto:[email protected]>
________________________________
Total Control Panel
Login<https://asp.reflexion.net/login?domain=selectconnect.net>
To:
[email protected]<https://asp.reflexion.net/address-properties?aID=750607761&domain=selectconnect.net>
From:
[email protected]<https://asp.reflexion.net/address-properties?aID=3098371613&domain=selectconnect.net>
Message Score: 1
High (60): Pass
My Spam Blocking Level: Medium
Medium (75): Pass
Low (90): Pass
Block<https://asp.reflexion.net/FooterAction?ver=2&bl-sender-address=1&rID=750607761&aID=3098371613&domain=selectconnect.net>
this sender /
Block<https://asp.reflexion.net/FooterAction?ver=2&ent=1&bl-sender-address=1&rID=750607761&aID=3098371613&domain=selectconnect.net>
this sender enterprise-wide
Block<https://asp.reflexion.net/FooterAction?ver=2&bl-sender-domain=1&rID=750607761&aID=3098371613&domain=selectconnect.net>
elecraft.com /
Block<https://asp.reflexion.net/FooterAction?ver=2&ent=1&bl-sender-domain=1&rID=750607761&aID=3098371613&domain=selectconnect.net>
elecraft.com enterprise-wide
This message was delivered because the content filter score did not exceed your
filter level.
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
