Hi Udo,
the mW calibration never worked on my K3 if using the K3 Utility. Don't
ask me why! Was the case right from the beginning. But it works
trouble-free when doing it the manual way from the radio front panel.
Try that as an alternative!
It seems to me settling power in the calibration routing just takes
longer than the Utility will wait while the front panel procedure does
not have that limit as you're in control of it.
Concerning the other issue (gain difference) just a few ideas: checks
internal preamp settings, check filter setting (do both RX have
comparable filter gains set), a.s.o.
73 & gl, Olli 'BQA
Contest, DX & radio projects: http://www.dh8bqa.de
Am 19.06.2015 um 22:50 schrieb Udo Langenohl - DK5YA:
Just got my KXV3-B as a replacement of the former KXV3-A. Installing
complete after 1 hour. Removing the back panel makes things much
easier btw. But there's an issue. The 1 mW calibration fails. Thats
what the Elecraft Utility says:
Elecraft K3 Utility Revision 1.13.5.9
OS Version 6.1 Build 7601 Windows 7/Windows Server 2008 R2
K3 MCU revision 05.26. RS-232 speed 38400 bit/s.
Starting 1 milliwatt calibration
Calibrating at 1.900 MHz
Calibration power settled at " 1.800.00;"
Elapsed time: 5 seconds
Tx Gain calibration failed because transmit power did not reach the
expected value
1 milliwatt calibration failed
Wait, there's more to come. I made a replacement because my guess was:
KXV3-A has a damage.
I use my K3 mostly on VHF with transverters, especially on 144 MHz
EME. I'm running a Xpol configuration with 4 antennas on 144 EME with
two identical transverters, both in phase and locked by a common
external LO with 10 MHz GPS control for Hpol and Vpol.
HPol RX is fed to the KXV3 XVTR In/Out while Vpol is fed to the AUX RF
input. I can listen to both planes simultaneously using diversity
receive.
But something very strange happens when I compare signals on both
planes. I have a 144 MHz beacon nearby (just 25 miles away). That
beacon is running 8 W on a Hpol antenna. On my Hpol (main RX via KXV3)
input this beacon comes up to S9+35 dB while on Vpol (second RX via
AUX) it's endstop (S9 +60dB). The beacon is in the line of sight,
there's a lot of RF on my location from this beacon.
It's definetely not from the transverters or from mismatched antennas
because when I change inputs and connect the Hpol transverter output
to the AUX RF it's suddenly S9 +60 dB too. Both main and sub RX are
exactly in the same configuration, filters, bandwidth, NB Off, etc..
I checked S/N on KXVR3-A (old board) and AUX few days ago with my
HP8664A signal generator.
On 28.200 (TVTR IF) I measured:
Top values:
KXV3-A TVTR IN: -10dBm = S9+25dB
AUX IN: -10dBm = S9+60dB (!)
KXV3-A TVTR IN: +3dBm = S9+60dB
Huge difference of at least 13dBm
Low values:
KXV3-A TVTR IN: -134dBm = signal detectable
KXV3-A TVTR IN: -140dBm = none
AUX IN: -140dBm = clear signal detectable
Again a difference of at least 6dB or even more.
Now, with the new KXV3-B it's even worse, at least 22 dB difference
between the AUX IN and TVTR IN.
What the heck is going wrong here? MAIN RX dead?
73 Udo, DK5YA
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
