If I understand the question I'm in data AFSK A 45wpm, connected to HRD DM780, I can hear the RTTY on both the radio and computer, I think I have the radio tuned correctly because the Text is about 70-80% correct, I'm seeing callsign and report most of the time. Computer shows no data, I've done 45 FSK, 45 AFSK , both reverse, I'm not sure what I'm transmitting when I try that as I can't hear it. I found the APF button, it was hidden right in front of me :)
I did notice at first that I did NOT have RTTY audio at the computer. There's a bug in the audio device settings where changing the sample rate "fixes" it. Now I have RTTY audio but still no text.. On my earlier concern about possibly damaging something when connecting USB and RS232: I opened up and removed all of the I/O boards, they all passed the visual and sniff test, main board top and bottom pass visual and pass sniff test. I have noticed that my Mag Loop controller is acting funny so maybe I'll get lucky and that is it. Jerry Moore AE4PB, K3S - S.N. 010324 An Amatuer is - Considerate, Loyal, Progressive, Friendly, Balanced, and Patriotic. -----Original Message----- From: Don Wilhelm [mailto:[email protected]] Sent: Thursday, September 24, 2015 5:41 PM To: [email protected]; 'Elecraft Reflector' Subject: Re: [Elecraft] K3S - APF/RTTY question Jer, Which DATA sub-mode were you in? For RTTY, you would normally be in AFSK A and then you could activate the dual tone filter. I believe most use MMTTY for RTTY, but HRD/DM780, Fldigi and other waterfall oriented software can work as well. In AFSK A (or FSK D) the K3 is in LSB (normal for RTTY) unless you activate REV, and the K3 dial frequency is the mark frequency. Make certain that the mark frequency and rate in the K3 menu agree with your software application settings. Other soundcard data modes normally use DATA A where USB is the normal sideband. 73, Don W3FPR On 9/24/2015 12:35 PM, [email protected] wrote: > I was trying to work K3P on 80m RTTY last night (new mode for me) and > was struggling to understand the owner's manual. I don't fully > understand how to get the dual APF to display correctly and setup. At > one point the K3S appeared be decoding correctly sometimes as I would > sometimes see his call and 599. I rarely saw the correct station he > was calling and didn't consistently copy. I was never able to get HRD > to copy any of it. I was in Data mode and the CWT did show split > tuning but I struggled to get the right most set of bars to stay filled even after playing with the width/filter.. > > > > I'm sure this is just a learning process and I've tried several > websites on setting up for RTTY with no success. Anyone have a good > guide on the K3/S with/without HRD on RTTY? > > > Thanks in advance. > > > > > > Jerry Moore > > AE4PB, K3S - S.N. 010324 > > An Amatuer is - Considerate, Loyal, Progressive, Friendly, Balanced, > and Patriotic. > > > > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > [email protected] > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
