Yes, I had the same issue last weekend. I rec’d help from several listers
including Dick who showed me the proper syntax for n1mm. Below is the function
key file I used with n1mm.
#NEW VERSION, This Function Key File requires N1MM Logger V12.02.00 or newer
#EDITS REQUIRED, before using this file-----------------------------------------
#SPECIAL INSTRUCTIONS, ---------------------------------------------------------
#REM, non-ESM mode <Enter> logs the contact and clears the QSO Entry window
#REM, S&P F1 calls CQ and automatically places the program in RUN mode
#REM, Designed to work in either ESM or non-ESM mode
#REM, F2 F3 F4 F5 use "!" macro for his callsign
#REM, F2 F7 {SENTRST} defaults to 599 or allows manual entry of sig report
#REM, I have shown examples of using "*", "!" as well as {MYCALL}and
#REM, (CALL) for call signs.
#REM, I use MMVARI for digital modes with n1mm because it will
#REM, work with RTTY and PSK31.
#REM, Use DATA sub-mode FSK-D with this file. The file also
#REM, will work with DATA sub-mode PSK-D as well as CW.
#REM, RUN MESSAGES, Run Messages begin here
-----------------------------------------
F1 Run CQ,{CATA1ASC KY ~CQ CQ RU {MYCALL} {MYCALL} CQ <04>;K30;}
F2 Run Exch,{CATA1ASC 599 VA VA <04>;K30;}
F3 Run TU,{CATA1ASC KY {CALL} TU {MYCALL} QRZ <04>;K30;}
F4 Run MyCall,{CATA1ASC KY {MYCALL} <04>;K30;}
F5 His Call,{CATA1ASC KY ! }
F6 -, -
F7 My Exch,{CATA1ASC KY {SENTRST} {EXCH} {SENTRST} {EXCH} <04>;K30;;}
F8 Agn?, {CATA1ASC KY AGN? AGN ? <04>;K30;}
F9 Number?,{CATA1ASC KY NUMBER # <04>;K30;}
F10 State?,{CATA1ASC KY STATE/PROV ??? <04>;K30;}
F11 STOP, {CATA1ASC K31;SWT16;}
F12 Wipe, {WIPE}
#S&P MESSAGES, Search and Pounce Messages begin here ---------------------------
F1 S&&P CQ,{CATA1ASC KY CQ RU * * CQ <04>;K30;}
F2 S&&P Exch,{CATA1ASC KY ! 599 VA 599 VA <04>;K30;}
F3 S&&P TU,{CATA1ASC KY TU * QRZ <04>;K30;}
F4 S&&P MyCall,{CATA1ASC KY NR4C * * <04>;K30;}
F5 His Call,{CATA1ASC KY ! <04>;K30;}
F6 -, -
F7 My Exch,{CATA1ASC KY 599 VA 599 VA <04>;K30;;}
F8 Agn?, {CATA1ASC KY AGN? AGN ? <04>;K30;}
F9 Number?,{CATA1ASC KY NUMBER # <04>;K30;}
F10 State?,{CATA1ASC KY STATE/PROV <04>;K30;}
F11 STOP, {CATA1ASC K31;SWT16;}
F12 Wipe, {WIPE}
The "<04>;” is a ^D or ctrl-D which is an EOT (end of transmission) character
from ‘days of olde’ i’m told. The brackets indicate HEX base.
I realize these are for n1mm, your software may be totally different. Hope
this helps, some.
…bill nr4c
> On Jan 6, 2016, at 11:55 PM, Rich <[email protected]> wrote:
>
> I am trying to use the KY command with Writelog for RTTY contesting. I have
> no problem setting up a Keyboard shortcut which then sends the data in the KY
> command, however I cannot find a way to stop the K3 from transmitting after
> the command sends the data in KY. I see there is an RX; command to end the
> TX. I also tried a SWT16 to create a press of the XMIT button. I cannot
> find a syntax that works for combining the RX or SWT16 command at the end of
> my KY command. I do not want to use another key press. I was hoping to do
> it with one line of data.
>
> The command string does not appear to work with the KY command
>
> Neither of these formats with return to radio to RX.
>
> KY "callsign";RX;
> or
> KY "callsign;SWT16;
>
> Any thoughts?
>
> Rich
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[email protected]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
