What Joe said :) I suppose you could put "TX;" into a switch macro, too, restoring the ability to do this via a front-panel switch.
Wayne On Sep 27, 2016, at 4:22 PM, "Joe Subich, W4TV" <[email protected]> wrote: > On 9/27/2016 7:00 PM, Wayne Burdick wrote: > > There are three ways to transmit in FSK-D and PSK-D modes: > > *FIVE* ways in FSK-D: > > 4) assert PTT on the mic jack, rear panel PTT jack or CAT RTS/DTR > line if selected > > 5) Sent TX; to the CAT interface > > Both are used by common RTTY software (in FSK mode), like MMTTY. > > 73, > > ... Joe, W4TV > > On 9/27/2016 7:00 PM, Wayne Burdick wrote: >> XMIT was disabled only for FSK-D and PSK-D data submodes. It can still be >> used in DATA-A and AFSK-A submodes. >> >> There are three ways to transmit in FSK-D and PSK-D modes: >> >> 1. Keyer paddle >> >> 2. Message play (M1-M4 tap) or message repeat (M1-M4 hold) >> >> 3. Text packet from a host computer or macro (see KeYing command, KY<TEXT>) >> >> XMIT was disable for FSK-D and PSK-D as part of a much larger firmware >> makeover having to do with T/R, the USB port, and safe exit from transmit. >> >> If you need to test transmit while in these or any other modes, you can do a >> TUNE. >> >> 73, >> Wayne >> N6KR >> >> >> >> >> On Sep 27, 2016, at 1:02 PM, ab2tc <[email protected]> wrote: >> >>> Hi, >>> >>> Nobody has responded to this so I'll hop in with what I know. >>> >>> Apparently the XMIT button was disabled for all data modes in firmware >>> version 5.47 and all later versions. This has nothing to do with K3/K3S; >>> both are affected. >>> >>> AB2TC - Knut >>> >>> >>> jeff stai-2 wrote >>>> hi - I'm used to using this button to nudge the amp into auto tune/band >>>> change by toggling it on and off briefly. I am in data/FSK mode. It works >>>> fine on the older K3 but for some reason on the K3S I am getting an "N/A" >>>> on the display and nothing happens. Why would I be getting N/A? >>>> >>>> Thanks and 73 jeff wk6i >>>> >>>> -- >>>> Jeff Stai ~ >>> >>>> wk6i.jeff@ >>> >>>> Twisted Oak Winery ~ http://www.twistedoak.com/ >>>> Facebook ~ http://www.facebook.com/twistedoak >>> >>> >>> >>> >>> >>> -- >>> View this message in context: >>> http://elecraft.365791.n2.nabble.com/XMIT-button-not-working-tp7622859p7622868.html >>> Sent from the Elecraft mailing list archive at Nabble.com. >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to [email protected] >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [email protected] >> > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
