Joe, it seemed to fix it for the K3S at work. I'll do some more testing Monday. Please send detailed steps you performed and I'll emulate and report back. -Kevin (KK4YEL)
No trees were killed in the sending of this message. However, a large number of electrons were terribly inconvenienced ! > On Oct 28, 2016, at 15:48, Joe Subich, W4TV <[email protected]> wrote: > > >> On 10/28/2016 12:03 PM, Jim - N4ST wrote: >> Alas, I downloaded the K3S Beta 5.65B software and installed it, but it did >> NOT fix the muting problem for me when operating split mode with WJST-X. > > In which case, HRD is probably sending some other command that changes > DSP settings during transmit. You will probably need to document what > commands HRD is generating in response to WSJT-X and work with Elecraft > to determine which of those commands results in DSP changes. The 5.56 > beta changes were in response to documentation of commands by Commander > and another software package with the K3. > > I'd start with all commands from about 2 seconds before x:00 until x:05 > since HRD is so unpredictable and commands could be delayed or out of > order. > > *Any* application should know not to change things like split status, > mode (including data sub-mode), sideband, transmit VFO, etc. while > in transmit - whether directly or via an intermediary like Commander > or HRD but, as we've seen, application programmers tend to be sloppy > and not consider how the rig will react. > > 73, > > ... Joe, W4TV > > > >> I was using WSJT-X 1.7 dev 7005. >> I dropped back to the public release WSJT-X 1.6 and that did not work >> either. >> Using HRD 6.3.0.585 >> >> ____________ >> 73, >> Jim - N4ST >> >> >> -----Original Message----- >> From: Elecraft [mailto:[email protected]] On Behalf Of Wayne >> Burdick >> Sent: Thursday, October 27, 2016 12:10 >> To: Elecraft Reflector <[email protected]> >> Subject: [Elecraft] New K3 firmware with minor bug fixes (rev. 5.56) - >> looking for testers >> >> Hi all, >> >> We're looking for volunteers to test the latest K3 field-test firmware. >> Please review the recent release notes below. >> >> If you'd like to do testing because you'll be affected by these changes, or >> if you're just interested in helping us qualify the firmware for beta >> release, please contact me directly. >> >> 73, >> Wayne >> N6KR >> >> * * * >> >> K3 MCU 5.56 / DSP 2.88 / FPF 1.26, 10-26-2016 >> >> * SCANNING WORKS WITH FREQUENCIES BELOW 1.0 MHz. Previously, scanning would >> stall in this case. >> >> * REDUCED K-POD MACRO FLASH TIME: If text decode is enabled, then the >> length of time that K-Pod macro names are flashed is greatly reduced. This >> reduces the obstruction of text shown on VFO B. >> >> * DT, FR, and FT HOST COMMANDS DISALLOWED IN TX MODE: Previously, these >> commands (data submode, split off, and split on) could be sent to the K3 >> during transmit from software applications. This could sometimes cause side >> effects such as muting of transmit audio in DATA modes. >> >> K3 MCU 5.55 / DSP 2.88 / FPF 1.26, 10-20-2016 >> >> * KPOD WORKS IN REMOTE-RIG TERMINAL MODE: The K-Pod will now function >> correctly with a K3 or K3/0-mini being used as a remote-rig terminal. Basic >> functions of the K-Pod can be used, including switch tap / hold and VFO >> A/B/offset control. LEDs and AUX outputs of the terminal K-Pod are not yet >> supported. Note: At present, when switches on the terminal K-Pod are used, >> they will execute macros stored at the remote K3. This will be apparent when >> macro names are flashed on VFO B. >> >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html Message >> delivered to [email protected] >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [email protected] >> > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
