John, your PS comment made me laugh. Sounds like it might be broke now, so now you are going to have to fix it. :)
73, mike va3mw On Mon, Nov 7, 2016 at 5:35 PM, Joe Subich, W4TV <[email protected]> wrote: > > John, > > I hate to tell you to look for whatever you changed in your software > configuration. However, there is absolutely no difference in TX Focus > whether one is using a pair of FT-1000MP or a pair of K3s! > > My best guess would be that you have - in no particular order - > 1) set "Radio Nr" for the "MK2R Port" in N1MM to 1 or 2 instead > of "Both" > 2) failed to set the "Control" Port in Router to the same port > as you configured as the MK2R port in N1MM > 3) failed to set an MK2R port (Two Radio Protocol) in N1MM > 4) failed to enable the MK2R Port (check CW/Other) in N1MM > 5) failed to select "microHAM control protocol on COM port" on > the SO2R tab in microHAM Router > 6) failed to select "Auto" on TX Focus (MK2R front panel). > > N1MM Classic is no longer supported by the N1MM development team. > However, the example configuration for N1MM Classic and MK2R+ is > available here: > <http://www.microham.com/Downloads/MK2R_N1MM_USB_Setup.pdf> > > Since N1MM Classic and N1MM Logger+ can not be installed at the same > time, I can no longer provide updates/specific support for N1MM > Classic. > > 73, > > ... Joe, W4TV > > > > > On 11/7/2016 4:49 PM, John W2ID wrote: > >> Hi all, >> >> If you do not use N1MM and an MK2R(+) with at least one K3 radio, >> then you should probably skip the rest of this message, because it >> won't be relevant to you. >> >> I have been using N1MM (classic, under Windows XP) with my MK2R+ and >> a pair of Yaesu FT-1000MP's for a few years with good success. I >> have just replaced the two Yaesu radios with a K3 and a K3S. >> >> It took me the first 90 minutes of the Sweepstakes to get to the >> point where N1MM saw both of my radios and was able to send CW. >> Thankfully, I did get that far. But despite several more hours of >> playing with every setting I could think of, I could not figure out >> how to make the MK2R+ transmit on the proper radio in "Auto" mode, >> i.e. the radio that has transmit focus in N1MM. So I was forced to >> switch manually using the front panel buttons on the MK2R+. >> >> I know it seems like this issue should be posted on either the >> MicroHam or N1MM reflectors. However, my MicroHam device was working >> perfectly fine with N1MM with my Yaesu radios, and the problem only >> started happening when I switched over to the K3's. So I figured my >> best bet would be to reach out to people who have succeeded in making >> the MK2R and N1MM work properly with a couple of Elecraft radios, and >> this is where I can find that crowd! >> >> Can anyone who has been successful getting N1MM and an MK2R+ to work >> with a pair of Elecraft K3 or K3S radios please kindly either point >> me to a document showing how to do it, and what all the relevant >> settings are, or else perhaps share with me either some screen shots >> or photos of your configuration screens, or a copy of the page in >> your station configuration log where you documented all of this? I >> have found numerous docs online, but couldn't find any that address >> SO2R with an MK2R and a pair of Elecraft rigs. I have pulled out >> about as much hair as I can afford to pull out. >> >> Thanks! >> >> 73, >> >> John W2ID >> >> p.s. Yes, I am aware that I shouldn't still be using Windows XP. >> The PC is used only for contesting, I subscribe to the "if it ain't >> broke, don't fix it" philosophy. :-) >> > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
