Understood. The T1 manual indicates that you can manually initiate tuning remotely by pulling the ring of J3 to ground, so running an extra control line from the operating position to the remote T1 could work. It also details the protocol for sending band info to the T1 to recall the previous tuner settings on a per band basis. The special cable for the FT-817 uses this. The KX2 can be configured to send the current band out its serial port as a CAT command. I imagine one could build a device using an Arduino or similar to grab that CAT band data and send it to the T1 when requested.... Might be a fun project for someday. So many project ideas, so little time... 73 de W0ZF On Wed, Nov 15, 2017 at 8:11 AM Barry N1EU <[email protected]> wrote:
> Yes, different use case. All my KX's have the internal tuner. But I was > thinking of an antenna configuration which would benefit from having a T1 > mounted away from the operating position. > > 73, Barry N1EU > > On Wed, Nov 15, 2017 at 9:00 AM, Dave Fugleberg <[email protected]> > wrote: > > > Barry, I went through that thought exercise before I ordered my KX2, > since > > I already own a T1. In the end I ordered the internal tuner with the > KX2. I > > have not regretted it for a minute. No extra cables, batteries, or fuss. > > And it works very well. > > Since you're concerned about remoting the tuner, your use case might be > > different than mine, but for a grab and go portable radio, the internal > > tuner is the way to go. > > On Wed, Nov 15, 2017 at 5:02 AM Heinz Bärtschi < > [email protected]> > > wrote: > > > >> It is correct understood, Barry. > >> > >> 73, Heinz HB9BCB > >> > >> > >> > >> > Am 15.11.2017 um 11:44 schrieb Barry N1EU <[email protected]>: > >> > > >> > I'm looking for confirmation on how I understand the T1 would work > with > >> my > >> > KX2 or KX3. When I change bands, I will need to go through a manual > >> > re-tune process. The memories in the T1 won't automatically recall a > >> > setting based on the newly transmitted frequency. In the case of the > >> KX2 > >> > or KX3, I understand that the memories may speed up the re-tune > process > >> but > >> > it will still require me pressing the Tune button manually and I > >> wouldn't > >> > be able to mount the T1 remote to the operating position. The T1 will > >> only > >> > do an automatic recall of settings without a manual re-tune when used > >> with > >> > an FT817 with the special interface cable. A special interface cable > is > >> > NOT available for the KX2 or KX3. > >> > > >> > Do I have this right? > >> > > >> > Thanks & 73, > >> > Barry N1EU > >> > > >> ______________________________________________________________ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:[email protected] > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: http://www.qsl.net/donate.html > >> Message delivered to [email protected] > >> > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
