> > I was glad to see Wayne's post describing the fix for my problem, which > should work on the K3S. However, I am still not able to get the K3S paddle > input to the K3S keyer to appear in the K3 utility. I see the commands TT1; > or TT0; appear in the Command Tester window but still the K3S paddle keying > does not show up in the K3 Utility Terminal window. > > I am following Mr Cady's directions in his K3S and P3 book pgs 53 and > 81... I have re-installed the K3 Utility and retried several times but no > luck. The results remain as I described in my previous post below. > Thanks, Tom NB5Q
> > ------------------------------ > > Message: 5 > Date: Fri, 2 Mar 2018 21:06:41 -0700 > From: Tom Norris <[email protected]> > To: Elecraft List Server <[email protected]> > Subject: [Elecraft] K3 utility to monitor extended display of > characters sent from K3S keyer problem > Message-ID: > <CAMi8m32RoBetqvt86gxA8HcGCkKz7o3q3yoqdYg0FvA653o3iQ@mail. > gmail.com> > Content-Type: text/plain; charset="UTF-8" > > I'm beginning my learning curve with my new K3S Kit (after a trip to > Elecraft for them to correct the 400hz filter I put in backwards! Otherwise > it was a good, fun build). I'm wanting to practice CW sending and I am able > to see my K3S paddle input characters in the K3S VFO B. But I am not able > to receive the K3S paddle entered characters in the K3 Utility display. I > can enter and transmit characters via the keyboard in the K3 utility, see > them in the K3 Utility window and the K3S VFO B. I've tried the various > K3S Text Decode settings but was no help. I'm sure it's a setting > someplace, I've tried to search the archives but the posts I've found do > not address that part of the problem. > Thanks, Tom NB5Q > > > ------------------------------ > > Message: 23 > Date: Sat, 3 Mar 2018 09:08:25 -0800 > From: Gary Hawkins <[email protected]> > To: Wayne Burdick <[email protected]> > Cc: Elecraft Reflector <[email protected]> > Subject: Re: [Elecraft] Terminal decoding on KX3 paddle generated CW > Message-ID: <[email protected]> > Content-Type: text/plain; charset=utf-8; format=flowed > > Hi Wayne, > > Many thanks for that - this works a treat :). > > 73, > > Gary K6YOA > > > On 3/3/2018 8:05 AM, Wayne Burdick wrote: > > Gary, > > > > There is a way to do this. It works equally well on the K2, K3, K3S, > KX2, and KX3. > > > > 1. Go into the KX3 Utility ?Command Tester? window. (Or use any terminal > emulator application of your choice.) > > > > 2. Send the command ?TT1;? to the radio from the computer. This will put > the rig into a mode where both transmitted and received characters are > outputted to the serial port, including those sent with the keyer paddle or > message memories. > > > > 3. To turn this mode off, send ?TT0;?. > > > > Note that this feature works with the built-in PSK31/PSK63 and RTTY > modes of all of the rigs as well. > > > > If you decide to try making contacts using CW or the built-in data > modes, check out the ?Terminal? function of the Utility. It allows you to > use the computer?s keyboard rather than the keyer paddle. > > > > 73, > > Wayne > > N6KR > > > **************************************** > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
