I would add to that my comments: I think if you are chasing DX on sideband it might be helpful to also get either the 1.8 or 2.1 filter. These filters are effective at blanking out adjacent stations so you can hear the weaker DX signal.
I would not be afraid to go under the hood and add things as long as you don't have the second receiver. In my opinion the second receiver installation is very tricky. Clearances are very tight with the second receiver and installation is tricky. -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Wes Stewart Sent: Friday, May 11, 2018 2:53 PM To: [email protected] Subject: Re: [Elecraft] K3S - Help me decide on which options to purchase Since you've had a K3 before, you should have some insight as to how if fulfilled your needs. The radios are very similar, I have both and for the most part don't see a world of difference, other than the old one is more reliable. The K3S preamp is better if you care about the higher bands. I am mainly interested in chasing DX. Because I have a KPA500 and KAT500, I don't have a tuner in either radio, although obviously, the old K3 predates the external amp/tuner. Also, I don't have a second receiver. You can work DX, even with wide splits without one. I do it all the time. I would recommend the 2.8 kHz filter just because the symmetry is better and this affects TX opposite sideband rejection. I have a 400 Hz and a 250 Hz filter, only because I was given the latter. The 400 is fine for CW and optimum if you venture into RTTY. If you're only interested in a couple of bands you should be able to have matched antennas and won't need a tuner. If you want general coverage RX or are interested in the VLF stuff get the filter. But really, installing one later is a matter of removing a few screws from the top cover and plugging it in. The same is true of crystal filters except you have to remove two covers. Don't be afraid of this stuff. You have a ham license remember? Wes N7WS On 5/11/2018 12:49 PM, Michael Gillen via Elecraft wrote: > Hi guys, > > I’m looking to purchase a K3S in the near future and I would like y’alls > input on which options to include. I had a K3 before however due to financial > issues I had to sell it. Now I want to get back into radio again and I want > to get a K3S. > > I mostly get on the OMISS Nets on 40m however I want to also learn how to Dx > on 20m (and other bands?) soon. And I want to eventually start CW after I > teach myself how to CW. Those are my near term goals (next two years). One > consideration is that whatever I include when I order the K3S will be > installed and calibrated by Elecraft at the factory. If I added options later > I would have down time and cost of shipping and cost of the work as well (I > don’t really want to do it myself even though I did build my first K3). > > I am likely going to include the 2.7 filter. > > Other possible options are: > > Other filters > General Rx > Second Rx > ??? > > > Thanks, > Michael > KK6RWK ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
