Loose or poor quality PL-259. There are many which "look good" but are not. Always snug PL-259 connectors on the SO-239 such they are a bit more than finger tight. I use/have a pair of 4" Channel lock pliers on the desk.
Bob, K4TAX Sent from my iPhone > On Jun 3, 2018, at 9:58 AM, jeff griffin <[email protected]> wrote: > > FIXED ! This morning I went through the RF jumper cables. I didn't find any > issues after taking each one out and inspecting. So I went through all the > other Elecraft supplied cables and also found no issues. So just to be sure > I make a new set of RF jumper cables out of LMR-240. Hooked everything up > and the problem is now fixed. I then tried the jumper cables I replaced one > at a time and the problem didn't return. Go figure. So I put the new LMR-240 > jumpers back on and life is once again good in kb2mland... > > 73 Jeff kb2m > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of jeff griffin > Sent: Saturday, June 2, 2018 11:49 AM > To: [email protected] > Subject: [Elecraft] KPA500 and K3 SWR meters disagree > > I recently brought my KPA/KAT500 north for the summer and hooked up to my > trapped multiband fan dipole that I use here in NJ. I leave my K3 here for > remote use and use the amp at my winter home in Florida to use with my Flex > 6500 with a Steppir Vertical antenna without the KAT500 tuner. When I got up > here I installed the KIO3B option. The install went well with no issues, all > looked good so I connected the K3, P3, KAT500, and KPA500 with the Elecraft > provided cable set like I do every year. > > The issue I'm having is an SWR difference between the KAT500 and the K3. > For example if I use the K3's internal tuner I can on a chosen frequency > achieve an SWR of 1/1. I the put the internal K3 tuner in bypass mode and > take the KAT500 out of bypass and set to auto. I then use the xmit button on > the K3 to create a tune signal to be sent to the KAT500. The K3 then shows a > 1/1, the KAT500 about the same but the KPA500 which is in STBY mode shows > around 3/1. What this causes to happen is the Amp will fault out if I try to > use any power output. If I check the antenna with a trusted SWR meter I see > 1.3/1 at the frequency of use. I upgraded the firmware in all the devices in > use, I also did a reset of the KAT's stored frequencies memory, and checked > both the amp and tuner with the utility programs. I'm going to call Elecraft > on Monday, anyone have any ideas in the meantime I can try? > > 73 Jeff kb2m > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
