Greg-
ERR TXG problem resolved. The problem was the offset on the FL1
filter...I had it set for .86 rather than -.86. Once that was changed,
everything went like clockwork on the Transmitter Gain Alignment.
Thanks to you and so many others for your helpfulness.
73 es HNY,
Cary
-----Original Message-----
From: Greg [mailto:[EMAIL PROTECTED]
Sent: Tuesday, January 01, 2008 7:19 PM
To: H. Cary III
Subject: RE: [Elecraft] ERR TXG Message es tnx
I take it you mean the 2.7 kHz filter? There is no 2.5.
You have the Filter Offset set as a negative number in CONFIG?
Greg
-----Original Message-----
From: H. Cary III [mailto:[EMAIL PROTECTED]
Sent: Tuesday, January 01, 2008 4:02 PM
To: Greg
Subject: RE: [Elecraft] ERR TXG Message es tnx
See below, cary
-----Original Message-----
From: Greg [mailto:[EMAIL PROTECTED]
Sent: Tuesday, January 01, 2008 6:57 PM
To: H. Cary III
Subject: RE: [Elecraft] ERR TXG Message es tnx
Hhmmmm...Did you do it after the REF Oscillator calibration? Or before it?
AFTER but don't see how that would affect it....
Please also check that all the coax connectors are fully seated in the
correct sockets.
I'll do that after I eat some supper....
What filter do you have setup for TX and what slot is it
in? Is it setup for all bands?
2.5 and it is FL1, all bands
Greg
-----Original Message-----
From: H. Cary III [mailto:[EMAIL PROTECTED]
Sent: Tuesday, January 01, 2008 3:20 PM
To: Greg
Subject: RE: [Elecraft] ERR TXG Message es tnx
Greg-
That is exactly what I did and got the ERR TXG message on all bands at the
5-watt test level.
73 and HNY de Cary
-----Original Message-----
From: Greg [mailto:[EMAIL PROTECTED]
Sent: Tuesday, January 01, 2008 6:18 PM
To: H. Cary III; [email protected]
Cc: Richard AD7FZ
Subject: RE: [Elecraft] ERR TXG Message es tnx
Carey. You still need to do the TX Gain calibration. That's what is
causing your error. Page 46/47 of the manual. Set power to 5W and hold
TUNE for a couple seconds on ALL BANDS. Then, if you have the KPA3
installed, you need to do the same for ALL BANDS at 50W.
Let me know how it goes.
73
Greg
AB7R
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of H. Cary III
Sent: Tuesday, January 01, 2008 2:56 PM
To: [email protected]
Cc: Richard AD7FZ
Subject: [Elecraft] ERR TXG Message es tnx
The reference oscillator is now aligned with WWV - thanks to N0SS, W3FPR,
DJ7MGQ, and AD7FZ for responding so quickly - Tom talked me through it
thankfully.
I just did the Transmitter Gain calibration and get an error message - ERR
TXG - on all bands 160-6. So after passing all the tests/checks during the
build, I seem to be alignment challenged Even more frustrating is the
detail on the error message in the book says "it could affect one or two
bands (how about ALL?) and indicates a problem with band pass filter
alignment or one of the low pass filters. Could one of the J-pin connectors
be the first place to look?
BTW, the good news is the receiver in my K3 is absolutely fantastic! One
day, it'll all come together...
HNY & 73,
Cary, K4TM
K2-100 #5266
K3-100 #0178
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
