-------- Original Message --------
Subject: Re: [Elecraft] K3 - RX Problem after latest firmware update
Date: Mon, 10 Mar 2008 08:58:47 -0400
From: Ken K3IU <[EMAIL PROTECTED]>
To: Stewart Baker <[EMAIL PROTECTED]>
CC: AB7R <[EMAIL PROTECTED]>, Elecraft Reflector
<[email protected]>
References: <[EMAIL PROTECTED]>
Hi Stewart:
I just ran #202 with the latest firmware through your steps several
times and I cannot duplicate your problem. The receiver never goes dead
at any time.
73,
Ken K3IU
Stewart Baker wrote:
Greg,
Have re-installed V1.75 & V1.57 again, no change.
Here is a sequence which you might like to try:-
POWER
80m LSB 3780
NORM
LO CUT=0.15
SAV ALT1
NORM
TX ON/OFF
ALT1
TX ON/OFF
Receive may be dead at this point
If not continue with
Select USB
ALT1
TX ON/OFF
Receive dead
Switching bands, modes or NORM always restores receiver.
I do (from my point of view) hope that I am not the only one with
this funny..
73
Stewart G3RXQ
On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote:
Stewart,
Try installing the new firmware again. I just tried to recreate
your report
and the radio performs as expected...no problem with RX after a
transmit
with ALT1 set to 0.15 on the LO side.
73
Greg
AB7R
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Stewart
Baker
Sent: Sunday, March 09, 2008 11:32 AM
To: Elecraft Reflector
Subject: [Elecraft] K3 - RX Problem after latest firmware update
I am not sure if there is an obscure problem after the latest
MCU
and DSP update. Maybe others could check and see if it happens
to
them ?
Any band on SSB if I have the DSP set to ALT1 with the Low Cut
set
at 0.15 Hz , then after going onto transmit the receiver appears
to be dead. If I set the DSP to NORM by pressing the knob the
receiver suddenly bursts into life...
This happens whether there is any transmit audio or RF out.
73
Stewart G3RXQ
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
No virus found in this incoming message.
Checked by AVG.
Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date:
3/9/2008
12:17 PM
No virus found in this outgoing message.
Checked by AVG.
Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date:
3/9/2008
12:17 PM
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
