Wayne is working on this bug and it should be fixed in the next release.
Thanks!
73
Greg
Begin forwarded message:
From: Gregory Fischer <[email protected]>
Date: December 14, 2008 8:22:06 PM PST
To: "Dick Housden, W0NTA" <[email protected]>
Subject: Re: [Elecraft] Strange problem when switching modes from
VFO A to B
Dick, I was able to duplicate your report. I sent a note to Wayne
and I am sure it will be corrected.
Thanks for the info!
73
Greg
AB7R
On Dec 14, 2008, at 8:06 PM, Dick Housden, W0NTA wrote:
Jack,
You are correct. I have had the reports of pinched audio and just
cycle to
another band and back or switch sidebands and back and everything
is OK.
I have duplicated what you report:
VFO A on CW and VFO B on SSB.
Turn off K3 while on VFO A - CW.
Turn it back on and immediately switch to VFO B - SSB and the audio
is
terrible.
Cycle to other sideband and back and all is well again.
This only happens to me on 40, 80, and 160 meters. Other bands are
unaffected. Each time I have had a report of bad audio, it was on
40 meters.
Rarely operate 80 or 160 meters.
I am glad to find out how to get around this problem. I hope
something can
be done with programming to fix it, though.
73, Dick, W0NTA
Jack Colson wrote:
I have VFO A programmed for CW on each band, VFO B programmed for
SSB
(makes no difference which sideband ). Power up the K3 on VFO A
then
switch over to VFO B and the signal generated is extremely
distorted and
sounds like it is being transmitted via a very narrow filter. To
correct this problem simply switch the mode from L or USB to CW
and back
again to L or USB. Audio is then restored to normal. I have the
filters programmed correctly, the 2.7KHz filter is used for
transmit. I
am using the ESSB mode with a 4 KHz filter. This problem is
independent
of band.
I mentioned this to Gary who passed it onto Lyle and who was
unable to
make it happen. I am using firmware 2.38 DSP 1.92. I am waiting
for an
update which will fix the turn on audio spike before updating.
Any suggestions ? It is just a nuisance getting a report of who
is that
calling!!!
73,
Jack, W3TMZ
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
--
View this message in context:
http://n2.nabble.com/Strange-problem-when-switching-modes-from-VFO-A-to-B-tp1656359p1656737.html
Sent from the Elecraft mailing list archive at Nabble.com.
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
