I spend most of my time tinkering with the AGC-THR, AGC-SLP and RX-EQ - wish I had a dollar for every minute I've spent with the RX-EQ but that's The Other thread.
Matt Zilmer wrote: > > You have the satisfaction of knowing that your're right on the mark > then. Well... at least very close. AND you've been spot on the whole > time you've had the K3. > > Suggestion: Find somewhere else to tinker. The S-Meter is a good > target. There has been some debate on that. Same with AGC > adjustments. > > There is a lot to do here with the K3. Operating it is the best part. > I think Elecraft has found us a whole new hobby, or a set of them. > > 73, > matt, W6NIA > K3 #24, K2 #2810, etc. > > > On Mon, 15 Dec 2008 20:39:28 -0800 (PST), you wrote: > >> >>The multimeter *did* read 5.007 volts but I couldn't enter the additional 7mV >>into the K3. Talk about annoying.... >> >> >>Matt Zilmer wrote: >>> >>> Just use a different (uncalibrated) DMM.... Then you can change the >>> setting _twice_! >>> >>> matt zilmer, W6NIA >>> >>> On Mon, 15 Dec 2008 18:07:07 -0800 (PST), you wrote: >>> >>>> >>>>Don't you hate it when your calibrated multimeter displays 5.00V on pin 2 >>of >>>>the ACC connector and you then don't have a reason for altering the >>setting? >>>>I feel like I've missed out :) >>>> >>>> >>>>----- >>>>Shane >>>>K3/10: S/N 2127, KBPF3, KFL3B-FM, KFL3A-6K, KFL3A-2.8K, KFL3A-400, >>KTCXO3-1 >>>>& KXV3. >>> _______________________________________________ >>> Elecraft mailing list >>> Post to: Elecraft@mailman.qth.net >>> You must be a subscriber to post to the list. >>> Subscriber Info (Addr. Change, sub, unsub etc.): >>> http://mailman.qth.net/mailman/listinfo/elecraft >>> >>> Help: http://mailman.qth.net/subscribers.htm >>> Elecraft web page: http://www.elecraft.com >>> >>> >> >> >>----- >>Shane >>K3/10: S/N 2127, KBPF3, KFL3B-FM, KFL3A-6K, KFL3A-2.8K, KFL3A-400, KTCXO3-1 >>& KXV3. > _______________________________________________ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > > ----- Shane K3/10: S/N 2127, KBPF3, KFL3B-FM, KFL3A-6K, KFL3A-2.8K, KFL3A-400, KTCXO3-1 & KXV3. -- View this message in context: http://n2.nabble.com/K3%3A-ADC-Ref-calibration-tp1658417p1661575.html Sent from the Elecraft mailing list archive at Nabble.com. _______________________________________________ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
