Joe, Thanks for the corrections. It appears that his problem may be setup parameters, and what is selected on the K3 must match that being generated by the computer and the massaging that the interface may do as well.
73, Don W3FPR Joe Subich, W4TV wrote: > Don, > > >> MMTTY is soundcard generated data. >> > > Not entirely true. MMTTY can operate in "soundcard" mode > (AFSK), "UART" mode (FSK) or both at the same time. The > determining factor is the "TX Port" setting on the MISC > tab. "Sound" selects AFSK, "COM-TxD(FSK)" selects FSK > (if the proper COM number is selected for PTT & FSK on > the TX tab) and "Sound + COM-TxD (FSK)" selects both modes > of operation (e.g., using FSK but enabling the audio tones > for monitoring). > > >> The FSK D data mode is for true FSK generated using the >> keyer paddles, or the DIG 0 ACC input or ASCII data >> through the RS-232 port. >> > > microHAM interfaces provide "true" FSK (e.g., an on/off > keyed signal) to the DIG 0 (FSK) input on the ACC connector. > > 73, > > ... Joe, W4TV > > > > > >> -----Original Message----- >> From: elecraft-boun...@mailman.qth.net >> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Don Wilhelm >> Sent: Tuesday, August 18, 2009 3:37 PM >> To: Earl >> Cc: Elecraft >> Subject: Re: [Elecraft] K3 with MMTTY and microKEYER I >> >> >> Earl, >> >> MMTTY is soundcard generated data. Use DATA A or AFSK A >> (same as DATA A >> but optimized for RTTY). >> >> The FSK D data mode is for true FSK generated using the keyer >> paddles, >> or the DIG 0 ACC input or ASCII data through the RS-232 port. >> >> See the K3 manual section on Data Mode Selection. >> >> 73, >> Don W3FPR >> >> Earl wrote: >> >>> My new K3 #3223 is up and running 'mostly'. >>> >>> The short of it is that the K3 outputs a solid tone (like >>> >> tune) when >> >>> keyed by >>> MMTTY instead of FSK tones. MMTTY keys the radio OK and the >>> >> tone produces >> >>> power out of the radio. >>> >>> I am new to the K3 but not to MMTTY and microkeyer Router. (Past >>> FT1000MP user) >>> >>> K3 is set for DATA/FSK D >>> >>> MMTTY (ver1.65D) is set for COM-TxD(FSK). The comports >>> >> follow the MH >> >>> router >>> settings. The radio selected is Kenwood. MMTTY does read >>> >> the frequency so I >> >>> feel they are talking. >>> >>> microKEYER Router is set at CAT com3 and FSK com5 with PTT checked. >>> Audio >>> switching is BBB. The green LED's on the MK are flashing >>> >> with the FSK output >> >>> it is just not making it to the radio. >>> >>> TIA for your help. >>> >>> Earl N5ZM >>> >>> >>> >> ---------------------------------------------------------------------- >> >>> -- >>> >>> >>> No virus found in this incoming message. >>> Checked by AVG - www.avg.com >>> Version: 8.5.392 / Virus Database: 270.13.60/2311 - Release >>> >> Date: 08/18/09 06:03:00 >> >>> >>> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ------------------------------------------------------------------------ > > > No virus found in this incoming message. > Checked by AVG - www.avg.com > Version: 8.5.392 / Virus Database: 270.13.60/2311 - Release Date: 08/18/09 > 06:03:00 > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
