Thanks. Was also fighting this with many combinations between the K3 and N1MM. Never would have come up with the rts-dtr. Did a few Qs with the memory and paddle, may get a few in with N1MM. This got it keying.
73 de W3OU Steve -----Original Message----- From: Joe Subich, W4TV <[email protected]> To: [email protected]; [email protected] Sent: Sun, Nov 8, 2009 3:53 pm Subject: Re: [Elecraft] K3 and N1MM help please Dave, > My N1MM settings are: Com 1, K3, no checks, 4,800, N, 8, 1, > DTR Always On, RTS Always Off. You need to set N1MM Logger to DTR=CW and RTS=PTT and check CW on the radio port (uncheck CW on all other ports). > My K3 PTT-KEY setting is rts - OFF. I've tried about every > PTT--KEY setting there is and none of them work. With the change to N1MM Logger, you need to set the PTT-KEY in the K3 to rts-dtr. 73, ... Joe, W4TV > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of > [email protected] > Sent: Sunday, November 08, 2009 3:02 PM > To: [email protected] > Subject: [Elecraft] K3 and N1MM help please > > > I can't get my K3 to respond to the N1MM "F" keys. The F > keys are all > programmed and when I press one, the red TX light on the K3 > lights up, the > receiver mutes, but there's no transmit signal on CW -- I > haven't tried SSB > yet. The frequency on the K3 tracks fine in N1MM. The K3 is > NOT in test > mode, the CW icon is on, VOX is on, QSK is on. > > My N1MM settings are: Com 1, K3, no checks, 4,800, N, 8, 1, > DTR Always On, > RTS Always Off. Incidentally, N1MM suggests for a K3 that > both DTR and > RTS be on, but it didn't make any difference -- same result > both ways. Com 3 > is not checked under radio, but is checked for CW, DTR=CW, > RTS=Always Off, > Tx=1. No other Com ports have checks of any kind. > Incidentally, while my > reading of the N1MM instructions would make you think you > need a check for > Telnet, that is not the case. Telnet works fine without a > check. Packet > may not but I didn't check. > > My K3 PTT-KEY setting is rts - OFF. I've tried about every PTT--KEY > setting there is and none of them work. I must say that the > Config menu setting > in the K3 Owner's Manual (the latest, online) is really > inadequate in my > opinion. Two of my computer savvy friends worked on this > problem with me > and neither has come up with a solution. > > Hoping for some light at the end of the tunnel. > > 73, Dave > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
