That suggests that adding enough delay characters (~) after the SWT21; command (to allow the K3 to finish sending before receiving the ML000; command) should work. It's probably not practical, but I'll give it a try and report back.
73, Dave AB7E Iain MacDonnell - N6ML wrote: > On Fri, Nov 27, 2009 at 6:40 PM, David Gilbert <[email protected]> > wrote: > >> Send the description of the {END} command in the N1MM help file. I can't >> make it work for more than two sequential commands, though. >> > > Doesn't help when the voice message is being played by the KDVR3 > anyway - N1MM Logger really has no idea that that's infact what's > happening - it's just sending the commands that you specify to the > radio. > > ~Iain / N6ML > > > >> Iain MacDonnell - N6ML wrote: >> >> Hi John, >> >> I suspect what's happening here is that the three commands are >> executed instantly, one after the other, so the monitor is turned on, >> the DVR message is kicked off, and the monitor is turned off again - >> *immediately*, while the DVR message is just starting. I don't know if >> there's any way to delay execution of the last command until the DVR >> message has finished. >> >> BTW, I have notes on KDVR3 + N1MM Logger at: >> >> http://www.dseven.org/ar/n1mm-kdvr3 >> >> I don't attempt any tricks with the monitor level, though. >> >> ~Iain / N6ML >> >> >> >> On Fri, Nov 27, 2009 at 9:09 AM, John Scott <[email protected]> wrote: >> >> >> To begin with, I'm not sure if this should be here or on the N1MM >> reflector (or both). >> >> I would like to have a macro that will, in effect, allow F1 ... F4 on >> the computer keyboard in N1MM to press the DVR keys for me so I don't >> have to reach for them,and to turn the monitor function so I can tell if >> I sent the right thing and when it ends and then turn the monitor >> function off so I don't have to listen to it all the time. >> >> So what I need are the following commands: >> >> 1. Turn on the monitor function so I can hear the output of the DVR in >> my headphones: ML010; should do it. >> >> 2. Emulate the tapping of M1 ... M4 as required: SWTnn; is the command >> where nn is one of 21, 31, 35 or 39. >> >> 3. Turn the monitor off: ML000; >> >> This macro would save reaching from the keyboard to the radio during a >> contest. I hit the wrong button a few times during the SS-SSB this past >> week-end! In effect, it would be just like CW where we do exactly what >> I am describing. I know the middle part of this works, because I can do it. >> >> Using the K3 utility the commands: ML010; SWT21;ML00; entered >> individually each into one of Macro 9,Macro 10 and Macro 11 work just >> fine. However, if I put these three commands into one Macro, the first >> and the last are ignored and only the DVR message is played. Nothing in >> the headphones. (It's the same for Macros 1 to 8 as for the others.) >> >> Now, in N1MM there is the macro command {CATA1ASC radio_commands}. >> According to the N1MM manual, there can be only one CATA1ASC command per >> macro, but that command may contain more than one radio command. >> >> In N1MM the command {CATA1ASC SWT21;} works perfectly when placed into >> the F1 key for SSB. (You must, however, put a space in the first >> character in the table when typing it. This is N1MM's cue NOT to look >> for *.wav file). Reference an earlier post from N6ML. >> >> Other other hand in N1MM the command (in F1) {CATA1ASC >> ML010;SWT21;ML000;} does not work at all. Nothing happens. >> >> Is this a bug in the K3, N1MM or is it intended to be that way in the >> first place and I am wasting my time? >> >> Any comments and help would be appreciated. >> >> John, VE1JS >> K3 # 3486 >> BTW Using FW Ver. 3.63 >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> >> >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> >> >> > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
