Perhaps related to 4 -- clicking on a spot in VFO-A bandmap turns off the sub-receiver if it's on.
--- On Tue, 1/5/10, Joe Subich, W4TV <[email protected]> wrote: > From: Joe Subich, W4TV <[email protected]> > Subject: Re: [Elecraft] k3 and N1MM question > To: "'Barry N1EU'" <[email protected]>, [email protected] > Date: Tuesday, January 5, 2010, 8:32 AM > > There are several other issues with N1MM Logger and the K3. > > > 1) N1MM Logger sets the "wrong" sideband when changing > bands > because it sets mode before changing > frequencies > 2) N1MM logger drops out of "run" when operating split and > > tuning VFO A (receive VFO) > 3) the UP/DN keys for moving RIT operate in a fixed 20 Hz > or 100 Hz step instead of the values set > in the N1MM > configuration. > 4) N1MM Logger does not follow the split/sub status set on > > the transceiver front panel (even though > support is > present in the K3 CAT protocol to > determine sub/split > status). > > 73, > > ... Joe, W4TV > > > > > -----Original Message----- > > From: [email protected] > > > [mailto:[email protected]] > On Behalf Of Barry N1EU > > Sent: Tuesday, January 05, 2010 10:46 AM > > To: [email protected] > > Subject: Re: [Elecraft] k3 and N1MM question > > > > > > > > Bob, you're touching on a couple of areas where N1MM > Logger's > > control of the K3 isn't "rock solid." > > > > The best you can probably do for now is to check the > config > > setting "dual rx always on." With that setting, > the subrx > > "should" stay on when a spot is > > grabbed. Personally, I'd like the > software to leave the > > subrx alone and > > allow me to control it manually, but haven't been able > to > > persuade the programmers. > > > > With the current N1MM implementation, you must use the > > > program to set and reset split mode via alt-f7. > Otherwise, > > it doesn't know of any changes to split status. > This is > > another area that needs programming attention. > > > > Hopefully, N1MM Logger will improve in these two areas > of K3 > > control in the near future. > > > > 73, > > Barry N1EU > > > > > > > > bob finger wrote: > > > > > > Unfortunately with N1MM if I click on a simplex > spot both split > > > and sub receiver are turned off. Anyone > know how I can > > defeat this so > > > radio stays in split mode? > > > > > > > -- > > View this message in context: > > http://n2.nabble.com/k3-and-N1MM-question-tp4255584p4255791.html > > Sent from the Elecraft mailing list archive at > Nabble.com. > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
