Hi Alicia, Michael, & Everyone, I've only seen that error once. I've just today upgraded to SpamSieve v2 after a hiatus during which I did only Emailer Mail Action filtering. I stopped using Spam Sieve after it got a little wild, and started trashing way too many good emails. I guess I let a couple false positives slip by uncorrected, and it trained itself from that, and them went wild trashing my new messages, even from friends & clients. I finally looked in the "spam" folder, and found the reason I was getting the occasional semi-nasty phone call for not responding to someone's emails. Since I probably should have been watching for false positives a bit closer, it's probably partly my fault, even though I was lured into assuming I had adequately trained SpamSieve well enough already.
Most of my spam (but not all, oh no, not all...) is a blank email with a HTML attachment. So I have a Claris Emailer Mail Action that says: if the sender is not in my address book, AND the message body does not contain a space, trash it. That's a pretty good rule for me, but it does accidentally trash a few things, such as notices of new replies to my messages on Apple's discussion board. Anyway... I installed the new SpamSieve today, and after it auto-imported my old corpus, I immediately "reset" the corpus, then imported the "seed spam" that comes with the program. I also made sure to trash the old SpamSieve AppleScripts, then install the new ones before Launching Claris Emailer. I wasn't sure how to reset the history, so I just set it to report as of today forward. To start I wanted to closely monitor SpamSieve, so instead of making a mail action for it to auto-filter, I started by selecting some emails & pulling the applescript menu to "SpamSieve - Color if Spam". That initially identified all selected messages as spam, so I ran the Applescript "SpamSieve- Add Good". I repeated those 2 steps for about 340 messages (it learned as we kept going) before I saw that "NSInternalScriptError" error. Since I already knew you were trying to hunt it down, I snapped a full screen photo of it, in case there is a clue anywhere. I can report that I was making a noncontiguous selection of 8 messages, one of which is a blank message with HTML attachment. I selected one, then skipped 4 messages, then selected 1, skipped 2, and selected 6. That's just how it happened. I'm not sure if any mail was coming in at the same time. I do have Emailer check for mail every 10 minutes. After snapping the screen photo, Ok-ing the err, and with the messages still selected, I ran the "SpamSieve-Color if Spam" script again, and it didn't error this time. Basic Environment: Mac G4/466, Mac OS X.2.0 900 MB ram Emailer 2.0v3 Newest SpamSieve, as of today. Installed over previous version, Corpus reset & seeded. Running SpamSieve manually only. I'm excited about the new features in SpamSieve, and am willing to give it another go. I wish applescript was faster though. It can take quite a while to evaluate even a dozen emails. I may rename the SpamSieve scripts to space them farther apart in the AppleScript menu; to make sure I don't hastily select exactly the wrong one. Best, Dave Nathanson Mac Medix On 9/15/03 8:41 PM, Alicia Gordon [EMAIL PROTECTED] tapped the keyboard to say: >Have any other Emailer users upgraded to the newly released SpamSieve 2? > >It has some very nice improvements, so I recommend it, EXCEPT for the bug >I'm experiencing, which I've been trying to troubleshoot today with >Michael Tsai. > >On certain spam msgs (6 out of the many received today), I get an >NSInternalScriptError while unpacking, which requires me to hit OK before >it will proceed unpacking. These msgs do not get marked as spam, and the >same error occurs if you then run the Add Spam, Color if Spam or Move if >Spam scripts (on those msgs). > >Michael has so far been unable to duplicate this with the logs I'm >sending him. > >So if any of you have upgraded and are or are not running into this, I'm >sure it would help in his further testing. > >Thanks! > >Alicia > >Alicia Gordon >Gordon Word Artists >French and Spanish Translation ___________________________________________________________________________ To unsubscribe send a mail message with a SUBJECT line of "unsubscribe" to <[EMAIL PROTECTED]> or <[EMAIL PROTECTED]>
