Hi Steven,
Thanks for the reply. You'll have to pardon my ignorance on the topic
since I am predominantly a Core user, and not so much an Emane user.
I provided the pluggable transport file because I was not sure where else
I can be enabling flow control. I am pretty sure the pluggable transport
is not being used for anything, and that I am using the virtual transport.
The RF Pipe NEM is the following, which shows it is using the virtual
transport:
/usr/local/share/emane/models/rfpipe/xml/rfpipenem.xml
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE nem SYSTEM "file:///usr/local/share/emane/dtd/nem.dtd">
<nem name="RF-PIPE NEM">
<mac definition="rfpipemac.xml"/>
<phy definition="universalphy.xml">
<param name="subid" value="2"/>
</phy>
<transport definition="transvirtual.xml">
<param name="mask" value="255.255.255.0" />
<param name="device" value="emane0" />
<param name="devicepath" value="/dev/net/tun" />
<param name="bitrate" value="0" />
<param name="flowcontrolenable" value="on"/>
</transport>
</nem>
I threw in flowcontrolenable to see if it did anythingŠ
The RFPipe MAC is as follows:
/usr/local/share/emane/models/rfpipe/xml/rfpipemac.xml
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE mac SYSTEM "file:///usr/local/share/emane/dtd/mac.dtd">
<mac name="RF-PIPE MAC" library="rfpipemaclayer">
<param name="enablepromiscuousmode" value="off"/>
<param name="datarate" value="1M"/>
<param name="jitter" value="0"/>
<param name="delay" value="0"/>
<param name="flowcontrolenable" value="on"/>
<param name="flowcontroltokens" value="10"/>
<param name="enabletighttiming" value="off"/>
<param name="pcrcurveuri" value="rfpipepcr.xml"/>
</mac>
This is the virtual transport xml:
/usr/local/share/emane/transports/virtual/xml/transvirtual.xml
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE transport SYSTEM
"file:///usr/local/share/emane/dtd/transport.dtd">
<transport name="Tap transport" library="transvirtual">
<param name="bitrate" value="0.0"/>
<param name="devicepath" value="/dev/net/tun"/>
<param name="device" value="emane0"/>
<param name="address" value="172.30.1.1"/>
<param name="mask" value="255.255.0.0"/>
<param name="flowcontrolenable" value="on"/>
</transport>
Thanks again.
Best,
Greg
On 10/30/13 7:54 PM, "Steven Galgano" <[email protected]> wrote:
>Greg,
>
>Flow control is not supported by the pluggable transport. Currently only
>the Virtual Transport has flow control support. While the two
>transports offer similar features, they are not the same.
>
> <transport definition="transpluggablevirtual.xml">
>
>--
>Steven Galgano
>Adjacent Link LLC
>
>
>On 10/30/2013 04:57 PM, Kuperman, Gregory - 0665 - MITLL wrote:
>> Hi Joe,
>>
>> Thanks for the response. Below is the file
>>/usr/local/share/emanetransplug/xml/transportdaemon-virtual.xml. Is this
>>the correct way to set it? I have also enabled it
>>
>> <?xml version="1.0" encoding="UTF-8"?>
>> <!DOCTYPE transportdaemon SYSTEM
>>"file:///usr/share/emane/dtd/transportdaemon.dtd">
>> <transportdaemon>
>> <instance nemid="1">
>> <param name="localaddress" value="localhost:50001"/>
>> <param name="remoteaddress" value="localhost:40001"/>
>> <transport definition="transpluggablevirtual.xml">
>> <param name="mask" value="255.255.0.0"/>
>> <param name="address" value="172.30.1.1"/>
>> <param name="plugin" value="transplugethernetframe.xml" />
>> <param name="pluginparam" value="broadcastmode:off"/>
>> <param name="flowcontrolenable" value="on"/>
>> </transport>
>> </instance>
>> </transportdaemon>
>>
>> I have also enabled it in
>>/usr/local/share/emanetransplug/xml/transportdaemon-virtual.xml
>> <?xml version="1.0" encoding="UTF-8"?>
>> <!DOCTYPE transportdaemon SYSTEM
>>"file:///usr/share/emane/dtd/transportdaemon.dtd">
>> <transportdaemon>
>> <instance nemid="1">
>> <param name="localaddress" value="localhost:50001"/>
>> <param name="remoteaddress" value="localhost:40001"/>
>> <transport definition="transpluggablevirtual.xml">
>> <param name="mask" value="255.255.0.0"/>
>> <param name="address" value="172.30.1.1"/>
>> <param name="plugin" value="transplugethernetframe.xml" />
>> <param name="pluginparam" value="broadcastmode:off"/>
>> <param name="flowcontrolenable" value="on"/>
>> </transport>
>> </instance>
>> </transportdaemon>
>>
>> Thank you again for your help.
>>
>> Best,
>> Greg
>>
>>
>>
>> _______________________________________________
>> emane-users mailing list
>> [email protected]
>> http://pf.itd.nrl.navy.mil/mailman/listinfo/emane-users
>>
_______________________________________________
emane-users mailing list
[email protected]
http://pf.itd.nrl.navy.mil/mailman/listinfo/emane-users
