sorry.. just a test ----- Original Message ----- From: "Webb, Trey" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, November 23, 2001 10:58 AM Subject: RE: Embperl and buffered output
> That was it! I had this section wrapped inside of table for positioning on > the page. Thanks all. > > -trey > > -----Original Message----- > From: Gerald Richter [mailto:[EMAIL PROTECTED]] > Sent: Thursday, November 22, 2001 1:45 AM > To: Webb, Trey > Cc: [EMAIL PROTECTED] > Subject: Re: Embperl and buffered output > > > > hey, > > Thanks for the reply. I went ahead and set those but still no dice. > > It just sits there until things are completed and then displays the whole > > page. Any other ideas? > > > > Make sure optEarlyHttpHeader and dbgFlushOutput are really set by inserting > > [+ $optEarlyHttpHeader +] > [+ $dbgFlushOutput +] > > in your page. Both must be 1, otherwise it can't work. > > Depending on the browser you use, it will not always directly display the > output (for example it will not work inside tables). Sometimes it helps to > add a longish comment: > > <!-- ---------------------------------------------------------------- --> > > or even longer. > > I use the above settings without problems in 1.3.x (again 2.0 will not work, > but you can use 1.x compatibility mode to get this in 2.0) > > Gerald > > P.S. Please answer also to the list > > > -----Original Message----- > > From: Gerald Richter [mailto:[EMAIL PROTECTED]] > > Sent: Wednesday, November 21, 2001 11:42 PM > > To: Webb, Trey; [EMAIL PROTECTED] > > Subject: Re: Embperl and buffered output > > > > > > > I am trying to have the results of a ping displayed in the browser > window > > in > > > realtime. I read somewhere that embperl buffers the page before sending > > it. > > > I ahve tried to disable this by setting EMBPERL_OPTIONS to include the > > > optEarlyHttpHeader, I also tried to use optRedirectStdout. Neither > seemed > > to > > > work. I get the page displayed after everything the ping is done. Any > > ideas > > > on what I am doing wrong? Sample is below. > > > > > > open( PING, "/usr/sbin/ping -I 1 $fdat{ ip } 100 5|" ) ; > > > while ( <PING> ) { > > > print OUT "$_<BR>\n"; > > > } > > > close(PING); > > > > > > > In 1.3.x set optEarlyHttpHeader in EMBPERL_OPTIONS and dbgFlushOutput in > > EMBPERL_DEBUG (the second one could also be set inside the page or turned > on > > and off during the page, using $dbgFlushOutput=1) > > > > 2.0 currently doesn't support this, because it works totaly different > > internaly. I am currently thinking about how to get this working with 2.0. > > This will be part of one of the next releases > > > > Gerald > > > > P.S. $| has _no_ effect when printing to OUT. (dbgFlushOutput does the > same > > for Embperls output stream) > > > > ------------------------------------------------------------- > > Gerald Richter ecos electronic communication services gmbh > > Internetconnect * Webserver/-design/-datenbanken * Consulting > > > > Post: Tulpenstrasse 5 D-55276 Dienheim b. Mainz > > E-Mail: [EMAIL PROTECTED] Voice: +49 6133 925131 > > WWW: http://www.ecos.de Fax: +49 6133 925152 > > ------------------------------------------------------------- > > > > > > > ------------------------------------------------------------- > Gerald Richter ecos electronic communication services gmbh > Internetconnect * Webserver/-design/-datenbanken * Consulting > > Post: Tulpenstrasse 5 D-55276 Dienheim b. Mainz > E-Mail: [EMAIL PROTECTED] Voice: +49 6133 925131 > WWW: http://www.ecos.de Fax: +49 6133 925152 > ------------------------------------------------------------- > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
