[EMAIL PROTECTED] wrote:
> Dear all,
>
> I have a Sherline mill with steppers and no encoders (ie. open loop)
> I am using a probe, and I patched emc2 so that, if the probe trips when in
> non probe move, emc2 estops, and saves my $120 probe from my fat fingers :)
>
> BUT at each estop, I was loosing steps which I felt was not acceptable. I
> found that in stepgen, when !enable, the component abruptly stop sending
> pulses; so I patched stepgen so that an estop respect maxaccel constraints;
> that worked very well and solved my problem.
>
> Some time ago, I told about that on #emc, but some people there suggested
> that when driving a 5 ton machine, an estop MUST stop the system ASAP, and
> anything else is simply not acceptable; which makes sense. So I kept using
> my patch, and did not published it.
>
> Then, last weekend, I upgraded to 2.1.3 from the CVS; stepgen has changed,
> so I had to redo the patch in another way. But in the meantime, I digged
> into HAL (absolutely superb design !!!) and I thought of an acceptable
> solution:
>
> - Create a HAL bit parameter named "smooth_estop" with a default value of 0
> - Change the tests "if(!enable)" to "if(!enable %% !smooth_estop)... else
> stop smoothly"
>
> PROS:
> - This does not change the behaviour of any .ini or .hal script
> - This does not change the timing when enabled, and just add a single test
> when estopped
> - This allows openloop steppers to ALWAYS keep a valid position; I did some
> tests, and on my sherline, going from full speed (480 mm/mn) to 0 takes
> about 0.08 mm, which I think is acceptable.
> - For activating the mod, there is a single line to add to the .hal file.
>
> CONS:
- More HAL pins attached to the stepgen module.
- Diluting the meaning of "estop". A ramped stop is not an
estop.
- Diluting the meaning of "enable". When you disable something,
you make its output zero, now. Not later, not after a ramp, NOW.
- Implementing a generic function (probe protection) in a stepper
specific way. Some guy with servos might also want this kind
of probe protection - this approach does nothing for him.
Here is another approach that you can do in entirely in HAL, without
changing any code, and works equally well for servos and steppers:
Use one mux2 block per axis. The position command from EMC goes to in0
of the mux. The output of the mux goes to stepgen, and to the mux's own
in1 input. The select pin of the mux is connected to the "oh-crap"
signal from the probe. ("oh-crap" means "probe touched something, but
I'm not probing") The "mux with one input connected to the output" is a
simple track/hold or latch circuit.
During normal operation, the mux select input is zero, and it faithfully
passes the position commands from EMC to the stepgen block (or the PID
block if you are running servos). If the probe hits something, the
select input becomes a one, and the mux begins reading its own output.
That means the command to stepgen freezes in its tracks. When the
position command stops changing, stepgen will stop the motor as quickly
as possible, while obeying the accel constraints. The stepgen enable
would continue to be used for true E-stop, where you absolutely must
stop now and reliability is more important than lost steps.
Since the stepgen would stop when the "oh-crap" signal went true, EMC
would trip on a following error. When that happens, EMC's position
command begins tracking the feedback, so restarting is as simple as
turning off the "oh-crap" signal, and jogging away from whatever you ran
into.
As an aside:
On a servo system, freezing the position command might even stop the
machine faster than disabling the PID and/or the servo amp, since the
PID can command negative power, not just zero power. The tradeoff is
speed for reliability. For an E-stop, you must cut off power - you
can't depend on the PID, since it depends on feedback. Perhaps the
reason the user hit estop is because an encoder just died and the motor
is running away.... But for probe protection, where a quick stop is
the key, freezing the position command will stop either a servo OR a
step machine as quickly as possible.
Regards,
John Kasunich
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
Emc-developers mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/emc-developers