Horst, If the device is power supply as described by Richard in his earlier email then you will need to comply with both EMC requirements in Australia (C-Tick) and electrical safety requirements (electrical authority approval).
EMC Compliance C-tick compliance is the responsibility of the importer/local Australian manufacturer. If you do not have a local distributor or local office of your company in Australia you will need to engage the services of an "Agent" who agrees to take responsibility for Australian EMC compliance. Electrical Safety Compliance/Approval (for "Declared Articles") If you have acceptable (i.e. acceptable to the approval authority here) test reports to the correct standards you can complete an application form and send it, with all the required supporting information, along with a sample of the device, to: You will need to send an application, Safety and Standards Branch Level 4, Fitzwillian Street PO Box 972 Parramatta, NSW, 2124 Tel: +61-2-9895-0702 Fax: +61-2-9895-0423 Email: [email protected] WWW: http://www.fairtrading.nsw.gov.au Best regards, Kevin Richardson Stanimore Pty Limited Compliance Advice & Solutions for Technology Products and Services (Legislation/Regulations/Standards) Ph: 02-4329-4070 (Int'l: +61-2-4329-4070) Fax: 02-4328-5639 (Int'l: +61-2-4328-5639) Mobile: 04-1224-1620 (Int'l: +61-4-1224-1620) Email: [email protected] [email protected] [email protected] (alternate internet) -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Monday, 12 February 2001 5:11 PM To: Kevin Richardson; [email protected]; [email protected] Subject: AW: AC Adapters in Australia Richard, one of my clients require approval for Australia. (C-tick mark). My understanding is, that I have to send the sample to Australia for approval. Do you know the adress of the appropriate department, organisation? Thank you in advance Horst Haug -----Ursprüngliche Nachricht----- Von: [email protected] [mailto:[email protected]]Im Auftrag von Kevin Richardson Gesendet: Dienstag, 16. Januar 2001 04:35 An: [email protected]; [email protected] Betreff: RE: AC Adapters in Australia Richard, If by AC Adapter you mean a "plug-pack" stand-alone SELV type power supply (i.e. an "Extra-Low Voltage Power Supply Unit") then it is a "Declared Article" and requires electrical approval (by one of the Australian State Electricity Authorities etc). I notice you picked up on "for business use only". Although the "Declared Articles" listing does say that such devices only fall under the Declared Articles listing if they are of a "household type", the Electricity Authorities consider all such devices can be of a "household type" unless they have a very unique means of connection between the AC Adapter and the equipment it supplies (i.e. most have relatively common means of connection enabling them to be used to power many other types of equipment, including household type equipment. My advice is - approval required Richard. Best regards, Kevin Richardson Stanimore Pty Limited Compliance Advice & Solutions for Technology Products and Services (Legislation/Regulations/Standards) Ph: 02-4329-4070 (Int'l: +61-2-4329-4070) Fax: 02-4328-5639 (Int'l: +61-2-4328-5639) Mobile: 04-1224-1620 (Int'l: +61-4-1224-1620) Email: [email protected] [email protected] [email protected] (alternate internet) -----Original Message----- From: [email protected] [mailto:[email protected]]On Behalf Of [email protected] Sent: Tuesday, 16 January 2001 8:42 AM To: [email protected] Subject: AC Adapters in Australia The subject is an AC adapter imported into Australia as part of non-telecom ITE for business use only. Is the AC Adapter for this particular application considered to be "declared" and thus subject to safety approval? Richard Woods ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected] ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected] ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected]
