Some low profile AC-DC manufacturers: Martek Vicor Lambda Pico
None of them are cheap; but if you want low profile, PCB mount, high reliability; then these are some viable suppliers. Chris Maxwell | Design Engineer - Optical Division email [email protected] | dir +1 315 266 5128 | fax +1 315 797 8024 NetTest | 6 Rhoads Drive, Utica, NY 13502 | USA web www.nettest.com | tel +1 315 797 4449 | > -----Original Message----- > From: Peter Merguerian [SMTP:[email protected]] > Sent: Tuesday, September 17, 2002 5:24 AM > To: 'Gert Gremmen'; Hans Mellberg; [email protected] > Subject: RE: PCI low profile dc-dc > > > Gert and Hans, > > In Hans's e-mail he specifies dc-dc convertors. In your e-mail, you specify > ac-dc convertor. I assume you mean mains ac - dc. > > For dc-dc there you need not purchase a medical grade convertor since I > assume you will have reinforced insulation between the patient aplied part > and the ac mains. > > For ac-dc, most convertors in the market are encapsulated and approved to > ITE requirements. Some are approved for operational insulation between input > and output, others for basic insulation between input and output and most > for reinforced insulation between input and output. Per IEC 60 601-1 there > are no internal creepage requirements and no long term aging tests for the > encapsulation like in IEC 60 950. If you choose a regular ITE ac-dc which > meets 4000 Vac dielectric strength betwen input and output and make sure you > have the clearance/creepage requirements for reinforced insulation between > input and output (8.0 mm clearance/creepage), then you have nothing to worry > about for isolation between patient applied parts and the mains. Of course, > leakage current is also an issue you have to take into consideration. > > > > This e-mail message may contain privileged or confidential information. If > you are not the intended recipient, you may not disclose, use, disseminate, > distribute, copy or rely upon this message or attachment in any way. If you > received this e-mail message in error, please return by forwarding the > message and its attachments to the sender. > > > > > > > PETER S. MERGUERIAN > Technical Director > I.T.L. (Product Testing) Ltd. > 26 Hacharoshet St., POB 211 > Or Yehuda 60251, Israel > Tel: + 972-(0)3-5339022 Fax: + 972-(0)3-5339019 > Mobile: + 972-(0)54-838175 > http://www.itl.co.il > http://www.i-spec.com > > > > > > -----Original Message----- > From: Gert Gremmen [mailto:[email protected]] > Sent: Saturday, September 14, 2002 12:07 PM > To: Hans Mellberg; [email protected] > Subject: RE: PCI low profile dc-dc > > > > May I add: > > Looking for a low profile ac-dc on board converter having a decent > medical approval i.e. more then basic insulation between primary > and secundary. Any suggestions for a manufacturer ? My client > is located in Malaysia . > Gert Gremmen > ce-test > > -----Original Message----- > From: [email protected] > [mailto:[email protected]]On Behalf Of Hans Mellberg > Sent: vrijdag 13 september 2002 21:22 > To: [email protected] > Subject: PCI low profile dc-dc > > > > I am designing a PCI card that requires the use of several on-board dc-dc > converters > for 24V, 48V and a varialble V. Any suggestions to sources are greatly > appreciated, > Thanks in advance > > > ===== > Best Regards > Hans Mellberg > Regulatory Compliance & EMC Design Services Consultant > By the Pacific Coast next to Silicon Valley, > Santa Cruz, CA, USA > office:831-454-9450, cell:408-507-9694, fax:831-454-0755 > > __________________________________________________ > Do you Yahoo!? > Yahoo! News - Today's headlines > http://news.yahoo.com > > ------------------------------------------- > This message is from the IEEE EMC Society Product Safety > Technical Committee emc-pstc discussion list.> > > Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ > > To cancel your subscription, send mail to: > [email protected] > with the single line: > unsubscribe emc-pstc > > For help, send mail to the list administrators: > Ron Pickard: [email protected] > Dave Heald: [email protected] > > For policy questions, send mail to: > Richard Nute: [email protected] > Jim Bacher: [email protected] > > All emc-pstc postings are archived and searchable on the web at: > http://ieeepstc.mindcruiser.com/ > Click on "browse" and then "emc-pstc mailing list" > > > > > ------------------------------------------- > This message is from the IEEE EMC Society Product Safety > Technical Committee emc-pstc discussion list. > > Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ > > To cancel your subscription, send mail to: > [email protected] > with the single line: > unsubscribe emc-pstc > > For help, send mail to the list administrators: > Ron Pickard: [email protected] > Dave Heald: [email protected] > > For policy questions, send mail to: > Richard Nute: [email protected] > Jim Bacher: [email protected] > > All emc-pstc postings are archived and searchable on the web at: > http://ieeepstc.mindcruiser.com/ > Click on "browse" and then "emc-pstc mailing list" > > ------------------------------------------- > This message is from the IEEE EMC Society Product Safety > Technical Committee emc-pstc discussion list. > > Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ > > To cancel your subscription, send mail to: > [email protected] > with the single line: > unsubscribe emc-pstc > > For help, send mail to the list administrators: > Ron Pickard: [email protected] > Dave Heald: [email protected] > > For policy questions, send mail to: > Richard Nute: [email protected] > Jim Bacher: [email protected] > > All emc-pstc postings are archived and searchable on the web at: > http://ieeepstc.mindcruiser.com/ > Click on "browse" and then "emc-pstc mailing list" ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Ron Pickard: [email protected] Dave Heald: [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://ieeepstc.mindcruiser.com/ Click on "browse" and then "emc-pstc mailing list"
