Art 16: Article 16 Working plan 1. In accordance with the criteria set out in Article 15 and having consulted the Consultation Forum referred to in Article 18, the Commission shall not later than 6 July 2007 establish a working plan which shall be made publicly available. The working plan shall set out for the following three years an indicative list of product groups which will be considered as priorities for the adoption of implementing measures. The working plan shall be amended periodically by the Commission after consultation with the Consultation Forum. 2. However, during the transitional period, while the first working plan referred to in paragraph 1 is being established, and, in accordance with the procedure laid down in Article 19 (2) and the criteria set out in Article 15, and after consulting the Consultation Forum, the Commission shall as appropriate introduce by anticipation: - implementing measures starting with those products which have been identified by the ECCP as offering a high potential for cost-effective reduction of greenhouse gas emissions, such as heating and water heating equipment, electric motor systems, lighting in both the domestic and tertiary sectors, domestic appliances, office equipment in both the domestic and tertiary sectors, consumer electronics and HVAC (heating ventilating air conditioning) systems; - a separate implementing measure reducing stand-by losses for a group of products.
Regards, Chris ____________ From: [email protected] [mailto:[email protected]] On Behalf Of Gordon,Ian Sent: 13 September 2005 09:57 To: 'IEEE EMC & SAFETY PSTC' Subject: EuP Directive All Does anybody know anything about this planned directive and whether it will apply to both industrial and domestic products? http://europa.eu.int/eur-lex/lex/LexUriServ/site/en/oj/2005/l_191/l_1912 0050 722en00290058.pdf Definitions For the purposes of this Directive the following definitions shall apply: 'Energy-using product' or 'EuP' means a product which, once placed on the market and/or put into service, is dependent on energy input (electricity, fossil fuels and renewable energy sources) to work as intended, or a product for the generation, transfer and measurement of such energy, including parts dependent on energy input and intended to be incorporated into an EuP covered by this Directive which are placed on the market and/or put into service as individual parts for end-users and of which the environmental performance can be assessed independently; Ian Gordon *********************************************************************** The information contained in this email and any attachments may be confidential and is provided solely for the use of the intended recipient(s). If you are not the intended recipient, you are hereby notified that any disclosure, distribution, or use of this e-mail, its attachments or any information contained therein is unauthorised and prohibited. If you have received this in error, please contact the sender immediately and delete this e-mail and any attachments. No responsibility is accepted for any virus or defect that might arise >from opening this e-mail or attachments, whether or not it has been checked by anti-virus software. - 2005 IEEE Symposium on Product Safety Engineering 3-4 October Schaumburg, IL http://www.ieee-pses.org/symposium This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/listserv/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas [email protected] Mike Cantwell [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc This message (including any attachments) may contain confidential information intended for a specific individual and purpose. If you are not the intended recipient, delete this message. If you are not the intended recipient, disclosing, copying, distributing, or taking any action based on this message is strictly prohibited. - 2005 IEEE Symposium on Product Safety Engineering 3-4 October Schaumburg, IL http://www.ieee-pses.org/symposium This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/listserv/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas [email protected] Mike Cantwell [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc
