The LISNMARK (LISN MATE) is exactly the same device as what I linked to. As for the current probes, comparing L and N to determine if one of cm or dm predominates... we are talking about noise signals, and measuring magnitudes (no phase info) in frequency domain, right? I know that on one conductor, you can say CM/DM add while they subtract on the other (mathematically correct no matter which you call L and which you call N). I'm confused at how you know it cannot be similar amounts CM and DM noise when the noise magnitude is the same between L and N. I'd appreciate it if you could explain.
Obviously running L+N simultaneously through the same probe gives common-mode noise, I'm not sure if I worded my response badly because I meant to say bullet #3 is completely correct (as is 1, along with 4 assuming no "LISNMATE") Elliott Martinson Product Assurance Specialist I Electronic Theatre Controls 3031 N PLEASANT VIEW RD MIDDLETON WI 53562-4809 Work: 608.824.5696 / Cell: 608.209.9897 [email protected] From: Ken Javor [mailto:[email protected]] Sent: Tuesday, March 29, 2016 4:14 PM To: [email protected] Subject: Re: [PSES] Commom mode current vs. differential mode current and LISN Disagree. Westin had it right. A current probe can be used to isolate either cm or dm current. If at any frequency the signal amplitude on individual line and neutral conductors are very close, then all you can say is that at that frequency either cm or dm predominates, but you can't say which. With a LISN, a separate device must be used. Mark Nave of EMC Services designed a three port device (connects to each LISN port and to the EMI receiver) trademarked LISNMATE in the 1980s to isolate common mode, and sometime later he produced LISNMARK, which isolated DM. Within the past decade, Ray Adams while at Fischer Custom Communications packed both functions in one piece of equipment, which if memory serves was named LISNUP. EMC Services, Mark Nave's company, is no longer producing his products, but I believe the FCC product is still available. Ken Javor Ph. (256) 650-5261 ________________________________ From: Elliott Martinson <[email protected]<mailto:[email protected]>> Reply-To: Elliott Martinson <[email protected]<mailto:[email protected]>> Date: Tue, 29 Mar 2016 20:36:18 +0000 To: <[email protected]<mailto:[email protected]>> Conversation: [PSES] Commom mode current vs. differential mode current and LISN Subject: Re: [PSES] Commom mode current vs. differential mode current and LISN http://www.hottconsultants.com/techtips/CM_vs_DM%20Conducted_Emission.html This is a great resource for your question. Your second point kind of contradicts your first, if it's trying to say what I think it is. DM and CM each show up on L, but the same is true for N. It's a linear combination of both, so even if L and N are almost equal, you can't say anything about the proportion of DM to CM currents. If they are not equal, then this implies current is travelling back via the ground conductor and/or energy's being lost to radiated emissions. What you need is a physical circuit to do the adding/subtracting of the LISN outputs. (otherwise your 3rd bullet point is correct) Your 4th bullet, well I refer you to the link above. Elliott Martinson Product Assurance Specialist I Electronic Theatre Controls 3031 N PLEASANT VIEW RD MIDDLETON WI 53562-4809 Work: 608.824.5696 / Cell: 608.209.9897 [email protected]<mailto:[email protected]> <[email protected]<mailto:[email protected]>> From: Amund Westin [mailto:[email protected]] Sent: Tuesday, March 29, 2016 1:23 PM To: [email protected]<mailto:[email protected]> Subject: [PSES] Commom mode current vs. differential mode current and LISN Please correct me, if I am wrong (that happens quite often ...): * Let one wire (L) pass through a current clamp, and you measure the combination of current mode and differential mode currents * Do the same with wire N. If L and N are (almost) equal, you either have major part of DM currents or major part of CM current * Let both wire (L and N) pass through a current clamp, and you measure the only CM current (DM is canceled) * When doing conducted emission test by LISN, you actually get what you get. LISN do not see the difference between CM or DM. From LISN measurements, you can't say if noise is CM or DM. B.regards Amund - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) <http://www.ieee-pses.org/list.html><http://www.ieee-pses.org/list.html> List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher <[email protected]<mailto:[email protected]>> David Heald <[email protected]<mailto:[email protected]>> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) <http://www.ieee-pses.org/list.html><http://www.ieee-pses.org/list.html> List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher <[email protected]<mailto:[email protected]>> David Heald <[email protected]<mailto:[email protected]>> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]<mailto:[email protected]>> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe)<http://www.ieee-pses.org/list.html> List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]<mailto:[email protected]>> Mike Cantwell <[email protected]<mailto:[email protected]>> For policy questions, send mail to: Jim Bacher <[email protected]<mailto:[email protected]>> David Heald <[email protected]<mailto:[email protected]>> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher: <[email protected]> David Heald: <[email protected]>
