Scott, Sorry, I am not familiar with what AMT2 is.
Best regards, Kevin Richardson Stanimore Pty Limited Compliance Advice & Solutions for Technology (Legislation/Regulations/Standards/Australian Agent Services) Ph: 02-4329-4070 (Int'l: +61-2-4329-4070) Fax: 02-4328-5639 (Int'l: +61-2-4328-5639) Mobile: 04-1224-1620 (Int'l: +61-4-1224-1620) Email: [email protected] or [email protected] URL: www.stanimore.com Confidentiality This material (this email including all attachments) may contain confidential and/or privileged information intended to be read or used by the addressees only. If you are not one of the intended recipients or you have received this material in error, any copying, disclosure, distribution, use of or reliance upon this material is prohibited. Please immediately notify Stanimore Pty Limited and delete/destroy all copies (electronic and hardcopy) of this email and all attachments. While the sender tries to ensure the accuracy of the information contained in this material, Stanimore take no responsibility for any actions taken as a result of receiving this material or for any consequence of its use. From: Scott Xe [mailto:[email protected]] Sent: Tuesday, 4 October 2016 6:55 PM To: Kevin.Richardson Cc: [email protected] Subject: Re: [PSES] Put product on the Australia's market Kevin, I got this requirement from an Australian customer who rejected the acceptance of safety report 3 months ago that needs to meet AMT2 in Nov 2016 at the latest. However the shipment arrives in Australia well before Nov 2016. Their reason is all the products on the selves or first introduced in Australia must comply with the new standard. This rule is quite different from EU - new standard does not apply to already arrived products. Regards, Scott On 4 October 2016 at 06:33, Kevin.Richardson <[email protected]> wrote: Hi Scott, Adding to Ted Eckert's, comments...... Not sure of the source of your information however, it would depend upon the Act or regulation and the nature of the change, i.e. if it is safety related it may well require compliance from the date the change was gazetted. Typically however, any change would allow a phase-in period during which on-sale and first introduced (newly arrived) products may comply with either the previous or new requirements. At the end of that specified phase-in period the new requirements would be mandatory. Changes to standards that are mandated by any Act/regulation are generally handled in a similar manner. Best regards, Kevin Richardson Stanimore Pty Limited Compliance Advice & Solutions for Technology (Legislation/Regulations/Standards/Australian Agent Services) Ph: 02-4329-4070 (Int'l: +61-2-4329-4070) Fax: 02-4328-5639 (Int'l: +61-2-4328-5639) Mobile: 04-1224-1620 (Int'l: +61-4-1224-1620) Email: [email protected] or [email protected] URL: www.stanimore.com Confidentiality This material (this email including all attachments) may contain confidential and/or privileged information intended to be read or used by the addressees only. If you are not one of the intended recipients or you have received this material in error, any copying, disclosure, distribution, use of or reliance upon this material is prohibited. Please immediately notify Stanimore Pty Limited and delete/destroy all copies (electronic and hardcopy) of this email and all attachments. While the sender tries to ensure the accuracy of the information contained in this material, Stanimore take no responsibility for any actions taken as a result of receiving this material or for any consequence of its use. From: Scott Xe [mailto:[email protected]] Sent: Monday, 3 October 2016 11:53 PM To: [email protected] Subject: [PSES] Put product on the Australia's market When there is an update to an Act or a applicable standard, it said it applies to both on-sale products meeting previous ones and newly arrived products on the effective date. The retailers must sell out all the stock before the effective date or return to the suppliers for alternation in compliance with the latest standard. Is there any legal document to endorse this rule? Thanks and regards, Scott - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher <[email protected]> David Heald <[email protected]> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher: <[email protected]> David Heald: <[email protected]>
