On Jan 29, 2008, at 1:54 PM, Alex Joni wrote: > I just removed the picture you had in the email, it was basicly > showing the > same things as the pastebin below. > > Now to answer your problem: > The lines you want are commented out in your hal file. > I bet if you remove the comment, it will work as it should. > Also note that I added the "-enable": > > linksp Xindex <= motenc.0.enc-00-index-enable > linksp Xindex => axis.0.index-enable > linksp Yindex <= motenc.0.enc-01-index-enable > linksp Yindex => axis.1.index-enable > linksp Zindex <= motenc.0.enc-02-index-enable > linksp Zindex => axis.2.index-enable
I'll give it a try. > > Regards, > Alex > > PS: Dave.. try to send textbased emails.. those don't have the size > issue :) Alex ... is there a way to get hal-show stuff to a text page w/o retyping? > > ----- Original Message ----- > From: Dave Engvall > To: Enhanced Machine Controller (EMC) > Sent: Tuesday, January 29, 2008 10:07 PM > Subject: Re: [Emc-users] EMC2 2.2.2 /motenc-100 > > > http://pastebin.ca/880373 > > > Is the hal file. > > > I have a screenshot of the hal show but pastebin won't take it.� > I'll attach here but I don't expect it to make it thru the server.� > > > As far as I can tell the index enables are not connected. > > > Dave > > > > > > > On Jan 29, 2008, at 11:26 AM, John Kasunich wrote: > > > Dave Engvall wrote: > > > > > Back to the shop: > First of all the home stuff in the .ini in case I've screwed > something� > up there: > > > HOME_OFFSET� � � � � � � 0.1 > HOME_SEARCH_VEL � � 0.1 > HOME_LATCH_VEL� � � � � -0.01 > HOME_USE_INDEX � � � � YES > HOME_IGNORE_LIMITS � � YES > > > All fine. > > > > > Now to halmeter: > � � � � � � � � � � � � � � � � not > homing� � � � � � homing > axis.0.index-enable� � � � � � � � � � F� > � � � � � � � � � T > correct > axis.0.homing� � � � � � � � � � � � F� > � � � � � � � � � T > correct > motenc.0.enc-00-index-enable� � � � � � F� � � > � � � � � � � F > WRONG - this index enable pin should be connected to the axis� > index-enable pin, so they should both be the same at all times. > > > motenc.0.enc-00-index� � � � � � � � T� � � > � � � � � � � T > don't know > > > motenc.0.count � � � � � � � � � � � > xxxxx� � � � � � � � counting > as expected > > > Xindex� � � � � � � � � � � � � � � > � F� � � � � � � � � � F > this is a signal name, but I don't know what you have the signal > connected to. > > > Stick the output of 'halcmd show' on a webpage somewhere (like� > http://pastebin.ca/ or http://pastebin.com ) and post the resulting > URL so we can see what you have.� I want to know why > axis.0.index-enable isn't the same as motenc.0.enc-00-index-enable. > I bet they're not connected. > > > Regards, > > > John Kasunich > > > ---------------------------------------------------------------------- > --- > This SF.net email is sponsored by: Microsoft > Defy all challenges. Microsoft(R) Visual Studio 2008. > http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > > > ---------------------------------------------------------------------- > --- > This SF.net email is sponsored by: Microsoft > Defy all challenges. Microsoft(R) Visual Studio 2008. > http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
