On 10/19/2013 3:42 AM, Sven Wesley wrote: > 2013/10/18 Dave Cole <[email protected]> > >> With all of this cartoon talk, I decided to load the flash viewer into >> my office LinuxCNC setup that is running on a Intel 330 dual core board >> (older and slower than a D525MW) and see if I can watch cartoons, while >> RUNNING the control program for my engraver (also in the office) which >> uses a LPT interface to stepper drives. >> >> Heck ya! >> >> http://picpaste.com/Screenshot-8-X5U3qx4m.png >> >> Notice that is a Samsung 27" screen running in full HD. Gotta love >> hardware acceleration!! :-) >> >> I don't know what you guys did to screw up your D525MW setups but I CAN >> watch cartoons now while running the engraver.. >> >> Someone try this with an Intel Cedarview 2500, 2700, or 2800 board and >> tell us if it works or not... >> >> Remember, this is a full HD screen. >> >> Not that this is a good idea ... but it is possible! >> >> Dave >> >> > My old and ripped Roadrunner movies are probably THE ONLY cartoons I can > view with the 525's. That's because they are ripped at such a low level > it's ridiculous. And the computer running the big router that I planned to > replace with one of these is still much faster than any of the 525's I have > now - and that computer is not to be considered fast. I installed one to my > wife's office as a writers desk, it wasn't even useful for that. So they > ended up in the basement as backup and file servers controlling a few disk > cabinets. That, they do very well without bugging me. > > When I bought them there was a long debate about their performance here at > the list. With a few tweaks suggested from others I could get them running > the thread test at 7000 for a short period of time and all of a sudden > everything jumped up to a good 26 000, at its best I got one test run to > stay at 15 000 without stressing it too much. > After that I ran all the graphics on another computer and had it running > pretty good (John's suggestion? don't remember). By then I was pretty tired > of them and I left the idea of using them in the workshop. > > It seems there are good and bad versions of the 525. > > /S
That pict I sent the link to was running Youtube streaming through a wireless connection while it was running my engraver.. I have a commercial customer who runs a D525MW to drive a large waterjet CNC cutter via the LPT port and that runs up to 700 ipm cutting lightweight foam. The drives are 1 KW servos. It has been running for three years now.. What are you using for a motherboard that is better?? I'm not married to the D525MW.. and I am always looking for better solutions. Besides, the D525MW will be difficult to get new in a year or so. Dave > ------------------------------------------------------------------------------ > October Webinars: Code for Performance > Free Intel webinars can help you accelerate application performance. > Explore tips for MPI, OpenMP, advanced profiling, and more. Get the most from > the latest Intel processors and coprocessors. See abstracts and register > > http://pubads.g.doubleclick.net/gampad/clk?id=60135031&iu=/4140/ostg.clktrk > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ October Webinars: Code for Performance Free Intel webinars can help you accelerate application performance. Explore tips for MPI, OpenMP, advanced profiling, and more. Get the most from the latest Intel processors and coprocessors. See abstracts and register > http://pubads.g.doubleclick.net/gampad/clk?id=60135031&iu=/4140/ostg.clktrk _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
