hmmm... yours look bigger than jeffs drawing , i dont have dual shaft motors , i wonder if adding a large damper at the other end of my screw would work, i have 2 dials , steel 1 in thick 3 in diameter a couple pieces of rubber and a nut should do it , i will put this on my list thanks gene
jeremy youngs On Thu, Feb 27, 2014 at 8:53 PM, jeremy youngs <[email protected]> wrote: > looked at it a dozen times in the last 2 yrs and didnt ever see the fender > washer item , i could have thought about going there but i was running to > an appointment and chaing down some batteries to go off grid i will check > it out gene . > > > > jeremy youngs > > > On Thu, Feb 27, 2014 at 8:06 PM, Gene Heskett <[email protected]> wrote: > >> On Thursday 27 February 2014 20:04:27 jeremy youngs did opine: >> >> > !!!!gene stated >> > FWIW, I have the mixed rubber washer/fender washer style dampers on my >> > motors except for the one on my A/B/C table. I should make another for >> > it, but I find its speed is adequate without it. They are a huge help >> > at soaking up the mid-band resonances that can cause a stall at 1/3rd >> > of full speed. Take them off the mill and I have to reduce the >> > maxvel's in the .INI to about 1/3 or 1/4. That is how important they >> > are! >> > >> > so i have to ask any pics or a link gene ? this sounds great !!! >> > >> > >> > >> > jeremy youngs >> > >> > On Thu, Feb 27, 2014 at 11:05 AM, Dave Cole <[email protected]> >> wrote: >> > > On 2/27/2014 6:17 AM, andy pugh wrote: >> > > > On 26 February 2014 06:11, a k <[email protected]> wrote: >> > > >> to make cnc mill faster in rep rap deposition, head will have 2 >> > > >> axis. >> > > > >> > > > I wonder if it would be possible to use some sort of pantograph >> > > > mechanism to achieve low-force fast-motion from a high-force >> > > > slow-motion milling machine system? >> > > >> > > Are you thinking of a variable ratio gearbox/drive - ala CVT auto >> > > transmission? >> > > >> > > Interesting idea.. :-) >> > > >> > > Dave >> >> In addition to my overly snarky reply, Jeff, at www.xylotex.com is where >> I >> got that idea, he has some pix on that page too. >> >> Cheers, Gene >> -- >> "There are four boxes to be used in defense of liberty: >> soap, ballot, jury, and ammo. Please use in that order." >> -Ed Howdershelt (Author) >> Genes Web page <http://geneslinuxbox.net:6309/gene> >> >> NOTICE: Will pay 100 USD for an HP-4815A defective but >> complete probe assembly. >> >> >> >> ------------------------------------------------------------------------------ >> Flow-based real-time traffic analytics software. Cisco certified tool. >> Monitor traffic, SLAs, QoS, Medianet, WAAS etc. with NetFlow Analyzer >> Customize your own dashboards, set traffic alerts and generate reports. >> Network behavioral analysis & security monitoring. All-in-one tool. >> >> http://pubads.g.doubleclick.net/gampad/clk?id=126839071&iu=/4140/ostg.clktrk >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > > ------------------------------------------------------------------------------ Flow-based real-time traffic analytics software. Cisco certified tool. Monitor traffic, SLAs, QoS, Medianet, WAAS etc. with NetFlow Analyzer Customize your own dashboards, set traffic alerts and generate reports. Network behavioral analysis & security monitoring. All-in-one tool. http://pubads.g.doubleclick.net/gampad/clk?id=126839071&iu=/4140/ostg.clktrk _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
