On Friday 07 March 2014 21:04:23 Bill did opine: > Hi Gene > > I've attached it as a PDF > > Bill > Looks like and reads like the same motor as my html link below. And at only 24 volts, the speed is perhaps 200 rpm maximum. I'm with Andy over across the pond, thats awful small.
And that 24 volts, that is 9 more than the ULN2003 will be happy at unless enough series resistance is inserted in the common leg of the motor to make sure the total currents do not exceed 500ma. Otherwise the chip will break its mirror and let out the smoke. Without the smoke, they never work again. Can you put a pix of this machine up one of the pastebin's.? Set it to expire in 2 or 3 days and post the link pastebin gives you. Put something on the table, like a 12 oz can of soda so we can judge scale a bit better. > > > -------Original Message------- > > From: Gene Heskett > Date: 8/03/2014 10:48:23 AM > To: [email protected] > Subject: Re: [Emc-users] Linuxcnc stepper mill configuration > > On Friday 07 March 2014 19:22:40 Bill did opine: > > Hi Gene > > > > Sorry the link got mixed up in the email so here it goes again, I've > > emailed it to myself as well so I can check it. > > > > http://www.robosoftsystems.co > > in/roboshop/media/catalog/product/pdf/Minebea%2014PM-M201%20Unipolar%2 > > 0M otor pdf > > Link still bummed here, > as I see it, it should be > > <http://www.robosoftsystems.co.in/roboshop/Minbea%2014PM- > M201%20Unipolar%20Motor.pdf> > > I haven't turned word wrap off, but that should work for 99% of the > email agents and browsers out there. You'll note that I surrounded it > with <>, and I added 2 periods that are missing in your text above. > > Except that it doesn't, lemme go find it again. > > The link from here, to the html page is: > > <http://www.robosoftsystems.co.in/roboshop/index.php/motor- > accessories/servo-stepper-motors/minebea-14pm-m201-unipolar-stepper- > motor.html> > > should get you to the web page of that motor. Where the .pdf's are I > haven't a clue. But I think from the model number that it is the same > motor. > > Is it? > > > Regards Bill > > > > PS Broncos won, after the very hot days of February this is not too > > bad. Mostly night games.B > > Hope you enjoyed it. I'm not that huge a football fan but must say I do > enjoy a well played, everyone equal game now and then. > > Cheers, Gene > -- > "There are four boxes to be used in defense of liberty: > soap, ballot, jury, and ammo. Please use in that order." > -Ed Howdershelt (Author) > Genes Web page <http://geneslinuxbox.net:6309/gene> > > NOTICE: Will pay 100 USD for an HP-4815A defective but > complete probe assembly. > > > ------------------------------------------------------------------------ > ----- > > Subversion Kills Productivity. Get off Subversion & Make the Move to > Perforce. > With Perforce, you get hassle-free workflows. Merge that actually works. > Faster operations. Version large binaries. Built-in WAN optimization > and the > freedom to use Git, Perforce or both. Make the move to Perforce. > http://pubads.g.doubleclick.net/gampad/clk?id=122218951&iu=/4140/ostg.cl > ktrk _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users Cheers, Gene -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> NOTICE: Will pay 100 USD for an HP-4815A defective but complete probe assembly. ------------------------------------------------------------------------------ Subversion Kills Productivity. Get off Subversion & Make the Move to Perforce. With Perforce, you get hassle-free workflows. Merge that actually works. Faster operations. Version large binaries. Built-in WAN optimization and the freedom to use Git, Perforce or both. Make the move to Perforce. http://pubads.g.doubleclick.net/gampad/clk?id=122218951&iu=/4140/ostg.clktrk _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
