Thanks Ralph, certianly given me some ideas, and just as i thought not as easy as first thoughts
On 19 September 2014 17:59, <p...@wpnet.us> wrote: > > Picture here: > http://gympiemodelflyers.wordpress.com/articles/brushless-motors/ > > ------Original Mail------ > From: "Dave Caroline" <dave.thearchiv...@gmail.com> > To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net> > Sent: Fri, 19 Sep 2014 17:53:53 +0100 > Subject: Re: [Emc-users] brushless motor coil winder > > I do have one relevant picture already though, this shows they are > wound before placing on the armature and field for tis particular > design > > http://www.collection.archivist.info/archive/Lucas/PS/PA11/ps1636.jpg > > Dave > > On 19/09/2014, Dave Caroline <dave.thearchiv...@gmail.com> wrote: > > Thinking of thick wire, I do have some as yet unscanned pictures of > > (Lucas) starter motor winding machines. > > > > Dave Caroline > > > > On 19/09/2014, Kirk Wallace <kwall...@wallacecompany.com> wrote: > >> On 09/19/2014 09:11 AM, Dave Caroline wrote: > >>> I dont think it is much worse than any other, you just join the groups > >>> of coils together differently. > >>> > >>> Often the coils are wound off the rotor/stator and then mounted and > >>> varnished to keep steady. > >>> > >>> Reverse engineer (unwind) one to see how they did it. > >>> > >>> > >>> Dave Caroline > >>> > >>> On 19/09/2014, David Armstrong <cncbas...@gmail.com> wrote: > >>>> Guys, > >>>> iv'e been asked to come up with a coil winder for rc brushless motors > >>>> has anyone done such a winder , specific to rc brushless ,as these are > >>>> 3 > >>>> phases > >>>> i fear it could get complicated > >>>> > >>>> Dave > >> > >> The RC motors I'm familiar with use a few turns of very thick wire and > >> would be a bear to wind mechanically. There may be a way to wind a coil > >> off the core then install it to the stator leg, but this not ideal. > >> Maybe form C shapes and weld them into a coil after they are installed? > >> > >> > >> -- > >> Kirk Wallace > >> http://www.wallacecompany.com/machine_shop/ > >> http://www.wallacecompany.com/E45/ > >> > >> > ------------------------------------------------------------------------------ > >> Slashdot TV. Video for Nerds. Stuff that Matters. > >> > http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk > >> _______________________________________________ > >> Emc-users mailing list > >> Emc-users@lists.sourceforge.net > >> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > > > > > ------------------------------------------------------------------------------ > Slashdot TV. Video for Nerds. Stuff that Matters. > > http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > ------------------------------------------------------------------------------ > Slashdot TV. Video for Nerds. Stuff that Matters. > > http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > ------------------------------------------------------------------------------ Slashdot TV. Video for Nerds. Stuff that Matters. http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
