I just did all of this, rebooted, and I still have nothing regarding a eth1 connection in the /sbin/config -a output.
I am running he latest version of master on my machine. Rick On 4/8/2015 11:01 AM, sam sokolik wrote: > THis has some really good info on setting up the nic.. Don't use the > manager gui. > > http://linuxcnc.org/docs/2.7/html/man/man9/hm2_eth.9.html > > Also - you need to be using 2.7+ of linuxcnc for Ethernet support. > > sam > > On 4/8/2015 9:56 AM, Rick Lair wrote: >> A few questions, on setting up a network connection and static IP >> >> 1. Should I use the Network Manager GUI, or should I modify the the >> /etc/network/interface file thru the terminal? >> >> 2. I have tried both of the above, and cannot get anything to come up >> under eth0 on the printout of /sbin/config -a. I looked at my test >> machine in my office, and that printout shows the eth0. Should I delete >> the Network manager utility, I see issues where one interferes with the >> other? >> >> 3. If I plug a network cable into the Ethernet port on the MB, shouldn't >> it recognize it's connected, and start working on its own? >> I pulled the board out, went in the office, threw together >> a PS, and peripherals, and it will not do anything network wise when >> plugging it into our network. >> >> >> Here I go again, climbing another almost vertical learning curve. >> >> Rick >> >> >> >> On 4/7/2015 2:36 PM, Peter C. Wallace wrote: >>> On Tue, 7 Apr 2015, Rick Lair wrote: >>> >>>> Date: Tue, 07 Apr 2015 14:14:58 -0400 >>>> From: Rick Lair <r...@superiorroll.com> >>>> To: Peter Wallace <p...@mesanet.com> >>>> Subject: Re: [Emc-users] 7i80 Setup ( Was PNCConf setup) >>>> >>>> I don't know if the SF server crashed or what, but here is the >>>> printout you asked about. >>>> >>>> Here is my printout, >>>> >>>> greenmill@greenmill:~$ /sbin/ifconfig -a >>>> lo Link encap:Local Loopback >>>> inet addr:127.0.0.1 Mask:255.0.0.0 >>>> inet6 addr: ::1/128 Scope:Host >>>> UP LOOPBACK RUNNING MTU:16436 Metric:1 >>>> RX packets:1894 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:1894 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:0 >>>> RX bytes:113732 (111.0 KiB) TX bytes:113732 (111.0 KiB) >>>> >>>> wlan1 Link encap:Ethernet HWaddr 54:27:1e:61:b9:6f >>>> inet addr:192.168.1.142 Bcast:192.168.1.255 Mask:255.255.255.0 >>>> inet6 addr: fe80::5627:1eff:fe61:b96f/64 Scope:Link >>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>>> RX packets:34073 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:11010 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:1000 >>>> RX bytes:6970707 (6.6 MiB) TX bytes:1200489 (1.1 MiB) >>>> >>>> greenmill@greenmill:~$ >>> OK so its not terribly suprising that you cant communicate with the >>> 7I80 since you have no active Ethernet interface, only active >>> interfaces are your WIFI and the loopback interface. >>> >>> I would launch the network manager, select wired and then add a >>> configuration for a static IP address on the available Ethernet NIC >>> >>> >>> Note that for initial communication (until you setup the 7I80's EEPROM >>> address to 10.10.10.10 and move W2 to select the new address) you will >>> have to disable your wireless since its IP address range overlaps the >>> 7I80s default IP address >>> >>> >>> >>> >>>> And the W1 and W2 jumpers haven't been touched, they are in the >>>> bottom position. >>>> >>>> Rick >>>> >>>> >>> Peter Wallace >>> Mesa Electronics >>> >>> (\__/) >>> (='.'=) This is Bunny. Copy and paste bunny into your >>> (")_(") signature to help him gain world domination. >>> > > ------------------------------------------------------------------------------ > BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT > Develop your own process in accordance with the BPMN 2 standard > Learn Process modeling best practices with Bonita BPM through live exercises > http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ > source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll & Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ------------------------------------------------------------------------------ BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
