Something's gone wrong with the website and our hosting provider
(Dreamcast) has disabled our site.  Our IT specialists have been called
home from vacation and injected with caffeine for a heroic,
around-the-clock debugging effort.

Stay tuned for more as this breaking story develops.


On 10/13/2015 05:55 PM, Dave Cole wrote:
> 
>   I just got this:
> 
> 
>   Forbidden
> 
> You don't have permission to access / on this server.
> 
> Additionally, a 403 Forbidden error was encountered while trying to use 
> an ErrorDocument to handle the request.
> 
> 
> 
> On 10/13/2015 7:49 PM, jrmitchellj . wrote:
>> I am getting "forbiden" message when I try to connect to it.
>> It worked fine earlier today.
>>
>> Ray
>> On Aug 26, 2015 12:50 AM, "Marius Liebenberg" <mar...@mastercut.co.za>
>> wrote:
>>
>>> I changed the input spindle frequency to 200Hz and fixed the scaling.
>>> The input frequency is given and not calculated as it wastes unnecessary
>>> time. It works very well now. I will use a fast opto coupler to drive
>>> the power source and hopefully I have a solution.
>>>
>>> #define MainPeriod 50  // measurement frame duration, milliseconds
>>> #define pulseInput  2   // input pin for pulseIn
>>> #define pulseOutput    4
>>>
>>> long previousMillis = 0;
>>> unsigned long duration = 0; // receive pulse width
>>> unsigned long outDuration = 0;
>>> long pulsecount = 0;
>>> long dc = 0;
>>>
>>> float Freq = 0.2e3;
>>> float T = 1 / Freq;
>>> void setup()
>>> {
>>>    pinMode(pulseInput, INPUT);
>>>    Serial.begin(19200);
>>>    pinMode(ledPin, OUTPUT);
>>>    analogWriteFrequency(4, 40000); //set the pwm frequency = 25usec
>>>    analogWriteResolution(10); // use the highest resolution
>>> }
>>>
>>> void loop()
>>> {
>>>    unsigned long currentMillis = millis();
>>>    if (currentMillis - previousMillis >= MainPeriod)
>>>    {
>>>     previousMillis = currentMillis;
>>>     dc = (duration / 5e-3)/1000;
>>>     dc = dc / 100;
>>>     outDuration = (dc * 1024)/100;
>>>     analogWrite(pulseOutput, outDuration);
>>>
>>>     // write current time and F values to the serial port
>>>     // not implimented for production but handy to see the frequencies
>>>
>>>     //Serial.print(currentMillis);
>>>     //Serial.print(" "); // separator!
>>>
>>>     /*Serial.print(dc);
>>>     Serial.print(" ");
>>>     Serial.print(pulsecount);
>>>     Serial.print(" ");
>>>     Serial.print(duration);
>>>     Serial.print(" ");
>>>     Serial.println(outDuration);*/
>>>
>>>     duration = 0;
>>>     pulsecount = 0;
>>>
>>>    }
>>>    // instead of single measurement per cycle - accumulate and average
>>>    duration += pulseIn(pulseInput, HIGH, MainPeriod * 900);
>>>    pulsecount++;
>>>
>>> }
>>>
>>>
>>>
>>>> On 25.08.15 14:27, Marius Liebenberg wrote:
>>>>>     Erik
>>>>>   I am getting to old to be a purist any more. I always use the
>>>>> platform
>>>>>   or chip with the best or most intuitive dev environment.
>>>>>   Short piece of code using a Teensy 3.0. I use the Visual Micro
>>>>> debugger
>>>>>   in Microsoft Visual Studio 2015 all running on the latest Arduino
>>>>>   environment.
>>>> <Chuckle>. Marius, I've feared I'm too old to learn the newfangled
>>>> Arduino environment, so I'm thrilled to see how you've leveraged it.
>>>> The speed of getting it going is very impressive. I should take a
>>>> closer
>>>> look at the environment - I think I've seen somewhere that it can be
>>>> used with the gnu toolchain.
>>>>
>>>> Erik
>>>>
>>>> ------------------------------------------------------------------------------
>>>> _______________________________________________
>>>> Emc-users mailing list
>>>> Emc-users@lists.sourceforge.net
>>>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>> ------------------------------------------------------------------------------
>>> _______________________________________________
>>> Emc-users mailing list
>>> Emc-users@lists.sourceforge.net
>>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>>
>> ------------------------------------------------------------------------------
>> _______________________________________________
>> Emc-users mailing list
>> Emc-users@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/emc-users
> 
> 
> ---
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
> ------------------------------------------------------------------------------
> _______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users
> 

-- 
Sebastian Kuzminsky

------------------------------------------------------------------------------
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to