I am using (2) 7i42TA boards as breakout boards to the 7i43. I have the estop-ext connected to P3-47(GPIO-47). I have one side of my estop switch connected to ground and the other side connected to P3-(TB2-23) (which should be P3-47 according to my reading). So, do I need to supply a pull-up for input pin?
I have attached my ini file and hal file following. Thanks, Alan INI start # Generated by PNCconf at Mon Mar 6 20:42:36 2017 # If you make changes to this file, they will be # overwritten when you run PNCconf again [EMC] MACHINE = myCNCLathe DEBUG = 0 [DISPLAY] DISPLAY = axis POSITION_OFFSET = RELATIVE POSITION_FEEDBACK = ACTUAL MAX_FEED_OVERRIDE = 2.000000 MAX_SPINDLE_OVERRIDE = 1.000000 MIN_SPINDLE_OVERRIDE = 0.500000 INTRO_GRAPHIC = linuxcnc.gif INTRO_TIME = 5 PROGRAM_PREFIX = /home/acondit/linuxcnc/nc_files PYVCP = pyvcp-panel.xml INCREMENTS = .1in .05in .01in .005in .001in .0005in .0001in LATHE = 1 POSITION_FEEDBACK = ACTUAL DEFAULT_LINEAR_VELOCITY = 0.250000 MAX_LINEAR_VELOCITY = 1.666667 MIN_LINEAR_VELOCITY = 0.010000 DEFAULT_ANGULAR_VELOCITY = 0.250000 MAX_ANGULAR_VELOCITY = 1.000000 MIN_ANGULAR_VELOCITY = 0.010000 EDITOR = gedit GEOMETRY = xyz [FILTER] PROGRAM_EXTENSION = .png,.gif,.jpg Greyscale Depth Image PROGRAM_EXTENSION = .py Python Script png = image-to-gcode gif = image-to-gcode jpg = image-to-gcode py = python [TASK] TASK = milltask CYCLE_TIME = 0.010 [RS274NGC] PARAMETER_FILE = linuxcnc.var [EMCMOT] EMCMOT = motmod COMM_TIMEOUT = 1.0 COMM_WAIT = 0.010 SERVO_PERIOD = 1000000 [HOSTMOT2] # **** This is for info only **** # DRIVER0=hm2_7i43 # BOARD0=7i43 [HAL] HALUI = halui HALFILE = myCNCLathe.hal HALFILE = custom.hal POSTGUI_HALFILE = postgui_call_list.hal SHUTDOWN = shutdown.hal [HALUI] [TRAJ] AXES = 3 COORDINATES = X Z LINEAR_UNITS = inch ANGULAR_UNITS = degree CYCLE_TIME = 0.010 DEFAULT_VELOCITY = 0.30 MAX_LINEAR_VELOCITY = 3.00 [EMCIO] EMCIO = io CYCLE_TIME = 0.100 TOOL_TABLE = tool.tbl #******************** # Axis X #******************** [AXIS_0] TYPE = LINEAR HOME = 0.0 FERROR = 0.5 MIN_FERROR = 0.05 MAX_VELOCITY = 1.0 MAX_ACCELERATION = 30.0 # The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION # If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger. STEPGEN_MAXVEL = 1.25 STEPGEN_MAXACCEL = 37.50 P = 50.0 I = 0.0 D = 0.0 FF0 = 0.0 FF1 = 1.0 FF2 = 0.0 BIAS = 0.0 DEADBAND = 0.0 MAX_OUTPUT = 1.25 # these are in nanoseconds DIRSETUP = 200 DIRHOLD = 200 STEPLEN = 1000 STEPSPACE = 2000 STEP_SCALE = 40000.0 MIN_LIMIT = -0.001 MAX_LIMIT = 4.5 HOME_OFFSET = 0.000000 HOME_SEARCH_VEL = -0.050000 HOME_LATCH_VEL = -0.016667 HOME_FINAL_VEL = 0.000000 HOME_USE_INDEX = YES HOME_IGNORE_LIMITS = YES HOME_SEQUENCE = 1 #******************** # Axis Z #******************** [AXIS_2] TYPE = LINEAR HOME = 0.0 FERROR = 0.5 MIN_FERROR = 0.05 MAX_VELOCITY = 3.0 MAX_ACCELERATION = 30.0 # The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION # If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger. STEPGEN_MAXVEL = 3.75 STEPGEN_MAXACCEL = 37.50 P = 50.0 I = 0.0 D = 0.0 FF0 = 0.0 FF1 = 1.0 FF2 = 0.0 BIAS = 0.0 DEADBAND = 0.0 MAX_OUTPUT = 3.75 # these are in nanoseconds DIRSETUP = 200 DIRHOLD = 200 STEPLEN = 1000 STEPSPACE = 2000 STEP_SCALE = 10000.0 MIN_LIMIT = -0.001 MAX_LIMIT = 19.0 HOME_OFFSET = 0.000000 HOME_SEARCH_VEL = -0.050000 HOME_LATCH_VEL = -0.016667 HOME_FINAL_VEL = 0.000000 HOME_USE_INDEX = YES HOME_IGNORE_LIMITS = YES HOME_SEQUENCE = 0 #******************** # Spindle #******************** [SPINDLE_9] P = 0.0 I = 0.0 D = 0.0 FF0 = 1.0 FF1 = 0.0 FF2 = 0.0 BIAS = 0.0 DEADBAND = 0.0 MAX_OUTPUT = 2000.0 ENCODER_SCALE = 400.0 OUTPUT_SCALE = 1 OUTPUT_MIN_LIMIT = 0 OUTPUT_MAX_LIMIT = 1 INI end HAL start # Generated by PNCconf at Mon Mar 6 20:42:36 2017 # If you make changes to this file, they will be # overwritten when you run PNCconf again loadrt trivkins loadrt [EMCMOT]EMCMOT servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[TRAJ]AXES loadrt hostmot2 loadrt hm2_7i43 ioaddr=0x378 ioaddr_hi=0 epp_wide=1 config="firmware=hm2/7i43-2/SVST4_4.BIT num_encoders=4 num_pwmgens=4 num_stepgens=4" setp hm2_7i43.0.pwmgen.pwm_frequency 20000 setp hm2_7i43.0.pwmgen.pdm_frequency 6000000 setp hm2_7i43.0.watchdog.timeout_ns 5000000 loadrt pid names=pid.x,pid.z,pid.s loadrt abs names=abs.spindle loadrt lowpass names=lowpass.spindle loadrt scale names=scale.spindle,scale.gear loadrt mux16 names=ratio_select addf hm2_7i43.0.read servo-thread addf motion-command-handler servo-thread addf motion-controller servo-thread addf pid.x.do-pid-calcs servo-thread addf pid.z.do-pid-calcs servo-thread addf pid.s.do-pid-calcs servo-thread addf ratio_select servo-thread addf scale.spindle servo-thread addf scale.gear servo-thread addf abs.spindle servo-thread addf lowpass.spindle servo-thread addf hm2_7i43.0.write servo-thread # external output signals # --- X-ENABLE --- setp hm2_7i43.0.gpio.035.is_output true net x-enable hm2_7i43.0.gpio.035.out # --- MACHINE-IS-ENABLED --- setp hm2_7i43.0.gpio.041.is_output true net machine-is-enabled hm2_7i43.0.gpio.041.out # --- ESTOP-OUT --- setp hm2_7i43.0.gpio.044.is_output true net estop-out hm2_7i43.0.gpio.044.out # external input signals # --- SPINDLE-MANUAL-CW --- net spindle-manual-cw <= hm2_7i43.0.gpio.032.in # --- SPINDLE-MANUAL-CCW --- net spindle-manual-ccw <= hm2_7i43.0.gpio.033.in # --- SPINDLE-MANUAL-STOP --- net spindle-manual-stop <= hm2_7i43.0.gpio.034.in # --- BOTH-HOME-X --- net both-home-x <= hm2_7i43.0.gpio.038.in # --- BOTH-HOME-Z --- net both-home-z <= hm2_7i43.0.gpio.040.in # --- PROBE-IN --- net probe-in <= hm2_7i43.0.gpio.046.in # --- ESTOP-EXT --- net estop-ext <= hm2_7i43.0.gpio.047.in #******************* # AXIS X #******************* setp pid.x.Pgain [AXIS_0]P setp pid.x.Igain [AXIS_0]I setp pid.x.Dgain [AXIS_0]D setp pid.x.bias [AXIS_0]BIAS setp pid.x.FF0 [AXIS_0]FF0 setp pid.x.FF1 [AXIS_0]FF1 setp pid.x.FF2 [AXIS_0]FF2 setp pid.x.deadband [AXIS_0]DEADBAND setp pid.x.maxoutput [AXIS_0]MAX_OUTPUT setp pid.x.error-previous-target true setp pid.x.maxerror .0005 net x-index-enable <=> pid.x.index-enable net x-enable => pid.x.enable net x-pos-cmd => pid.x.command net x-vel-cmd => pid.x.command-deriv net x-pos-fb => pid.x.feedback net x-output => pid.x.output # Step Gen signals/setup setp hm2_7i43.0.stepgen.00.dirsetup [AXIS_0]DIRSETUP setp hm2_7i43.0.stepgen.00.dirhold [AXIS_0]DIRHOLD setp hm2_7i43.0.stepgen.00.steplen [AXIS_0]STEPLEN setp hm2_7i43.0.stepgen.00.stepspace [AXIS_0]STEPSPACE setp hm2_7i43.0.stepgen.00.position-scale [AXIS_0]STEP_SCALE setp hm2_7i43.0.stepgen.00.step_type 0 setp hm2_7i43.0.stepgen.00.control-type 1 setp hm2_7i43.0.stepgen.00.maxaccel [AXIS_0]STEPGEN_MAXACCEL setp hm2_7i43.0.stepgen.00.maxvel [AXIS_0]STEPGEN_MAXVEL # ---closedloop stepper signals--- net x-pos-cmd <= axis.0.motor-pos-cmd net x-vel-cmd <= axis.0.joint-vel-cmd net x-output <= hm2_7i43.0.stepgen.00.velocity-cmd net x-pos-fb <= hm2_7i43.0.stepgen.00.position-fb net x-pos-fb => axis.0.motor-pos-fb net x-enable <= axis.0.amp-enable-out net x-enable => hm2_7i43.0.stepgen.00.enable # ---setup home / limit switch signals--- net both-home-x => axis.0.home-sw-in net both-home-x => axis.0.neg-lim-sw-in net both-home-x => axis.0.pos-lim-sw-in #******************* # AXIS Z #******************* setp pid.z.Pgain [AXIS_2]P setp pid.z.Igain [AXIS_2]I setp pid.z.Dgain [AXIS_2]D setp pid.z.bias [AXIS_2]BIAS setp pid.z.FF0 [AXIS_2]FF0 setp pid.z.FF1 [AXIS_2]FF1 setp pid.z.FF2 [AXIS_2]FF2 setp pid.z.deadband [AXIS_2]DEADBAND setp pid.z.maxoutput [AXIS_2]MAX_OUTPUT setp pid.z.error-previous-target true setp pid.z.maxerror .0005 net z-index-enable <=> pid.z.index-enable net z-enable => pid.z.enable net z-pos-cmd => pid.z.command net z-vel-cmd => pid.z.command-deriv net z-pos-fb => pid.z.feedback net z-output => pid.z.output # Step Gen signals/setup setp hm2_7i43.0.stepgen.02.dirsetup [AXIS_2]DIRSETUP setp hm2_7i43.0.stepgen.02.dirhold [AXIS_2]DIRHOLD setp hm2_7i43.0.stepgen.02.steplen [AXIS_2]STEPLEN setp hm2_7i43.0.stepgen.02.stepspace [AXIS_2]STEPSPACE setp hm2_7i43.0.stepgen.02.position-scale [AXIS_2]STEP_SCALE setp hm2_7i43.0.stepgen.02.step_type 0 setp hm2_7i43.0.stepgen.02.control-type 1 setp hm2_7i43.0.stepgen.02.maxaccel [AXIS_2]STEPGEN_MAXACCEL setp hm2_7i43.0.stepgen.02.maxvel [AXIS_2]STEPGEN_MAXVEL # ---closedloop stepper signals--- net z-pos-cmd <= axis.2.motor-pos-cmd net z-vel-cmd <= axis.2.joint-vel-cmd net z-output <= hm2_7i43.0.stepgen.02.velocity-cmd net z-pos-fb <= hm2_7i43.0.stepgen.02.position-fb net z-pos-fb => axis.2.motor-pos-fb net z-enable <= axis.2.amp-enable-out net z-enable => hm2_7i43.0.stepgen.02.enable # ---setup home / limit switch signals--- net both-home-z => axis.2.home-sw-in net both-home-z => axis.2.neg-lim-sw-in net both-home-z => axis.2.pos-lim-sw-in #******************* # SPINDLE S #******************* setp pid.s.Pgain [SPINDLE_9]P setp pid.s.Igain [SPINDLE_9]I setp pid.s.Dgain [SPINDLE_9]D setp pid.s.bias [SPINDLE_9]BIAS setp pid.s.FF0 [SPINDLE_9]FF0 setp pid.s.FF1 [SPINDLE_9]FF1 setp pid.s.FF2 [SPINDLE_9]FF2 setp pid.s.deadband [SPINDLE_9]DEADBAND net ratio_select.out pid.s.maxoutput setp pid.s.error-previous-target true setp pid.s.maxerror .0005 net spindle-index-enable <=> pid.s.index-enable net spindle-enable => pid.s.enable net spindle-vel-cmd-rpm-abs => pid.s.command net spindle-vel-fb-rpm-abs => pid.s.feedback net spindle-pid-out pid.s.output => scale.gear.in net gear-ratio ratio_select.out-f => scale.gear.gain setp ratio_select.in00 0.000500 setp ratio_select.in01 0.002000 net gear-select-a => ratio_select.sel0 net spindle-output <= scale.gear.out # ---PWM Generator signals/setup--- setp hm2_7i43.0.pwmgen.03.output-type 1 #setp hm2_7i43.0.pwmgen.03.output-type 3 setp hm2_7i43.0.pwmgen.03.scale [SPINDLE_9]OUTPUT_SCALE net spindle-output => hm2_7i43.0.pwmgen.03.value net spindle-enable => hm2_7i43.0.pwmgen.03.enable # ---Encoder feedback signals/setup--- setp hm2_7i43.0.encoder.03.counter-mode 0 setp hm2_7i43.0.encoder.03.filter 1 setp hm2_7i43.0.encoder.03.index-invert 0 setp hm2_7i43.0.encoder.03.index-mask 0 setp hm2_7i43.0.encoder.03.index-mask-invert 0 setp hm2_7i43.0.encoder.03.scale [SPINDLE_9]ENCODER_SCALE net spindle-revs <= hm2_7i43.0.encoder.03.position net spindle-vel-fb-rps <= hm2_7i43.0.encoder.03.velocity net spindle-index-enable <=> hm2_7i43.0.encoder.03.index-enable # ---setup spindle control signals--- net spindle-vel-cmd-rps <= motion.spindle-speed-out-rps net spindle-vel-cmd-rps-abs <= motion.spindle-speed-out-rps-abs net spindle-vel-cmd-rpm <= motion.spindle-speed-out net spindle-vel-cmd-rpm-abs <= motion.spindle-speed-out-abs net spindle-enable <= motion.spindle-on net spindle-cw <= motion.spindle-forward net spindle-ccw <= motion.spindle-reverse net spindle-brake <= motion.spindle-brake net spindle-revs => motion.spindle-revs net spindle-at-speed => motion.spindle-at-speed net spindle-vel-fb-rps => motion.spindle-speed-in net spindle-index-enable <=> motion.spindle-index-enable # ---Setup spindle at speed signals--- sets spindle-at-speed true # Use ACTUAL spindle velocity from spindle encoder # spindle-velocity bounces around so we filter it with lowpass # spindle-velocity is signed so we use absolute component to remove sign # ACTUAL velocity is in RPS not RPM so we scale it. setp scale.spindle.gain 60 setp lowpass.spindle.gain 1.000000 net spindle-vel-fb-rps => scale.spindle.in net spindle-fb-rpm scale.spindle.out => abs.spindle.in net spindle-fb-rpm-abs abs.spindle.out => lowpass.spindle.in net spindle-fb-rpm-abs-filtered lowpass.spindle.out #****************************** # connect miscellaneous signals #****************************** # ---HALUI signals--- net joint-select-a halui.joint.0.select net x-is-homed halui.joint.0.is-homed net jog-x-pos halui.jog.0.plus net jog-x-neg halui.jog.0.minus net jog-x-analog halui.jog.0.analog net joint-select-c halui.joint.2.select net z-is-homed halui.joint.2.is-homed net jog-z-pos halui.jog.2.plus net jog-z-neg halui.jog.2.minus net jog-z-analog halui.jog.2.analog net jog-selected-pos halui.jog.selected.plus net jog-selected-neg halui.jog.selected.minus net spindle-manual-cw halui.spindle.forward net spindle-manual-ccw halui.spindle.reverse net spindle-manual-stop halui.spindle.stop net machine-is-on halui.machine.is-on net jog-speed halui.jog-speed net MDI-mode halui.mode.is-mdi # ---coolant signals--- net coolant-mist <= iocontrol.0.coolant-mist net coolant-flood <= iocontrol.0.coolant-flood # ---probe signal--- net probe-in => motion.probe-input # ---motion control signals--- net in-position <= motion.in-position net machine-is-enabled <= motion.motion-enabled # ---digital in / out signals--- # ---estop signals--- net estop-out <= iocontrol.0.user-enable-out net estop-ext => iocontrol.0.emc-enable-in # ---manual tool change signals--- loadusr -W hal_manualtoolchange net tool-change-request iocontrol.0.tool-change => hal_manualtoolchange.change net tool-change-confirmed iocontrol.0.tool-changed <= hal_manualtoolchange.changed net tool-number iocontrol.0.tool-prep-number => hal_manualtoolchange.number net tool-prepare-loopback iocontrol.0.tool-prepare => iocontrol.0.tool-prepared HAL end ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
