On Mon, 11 Jan 2021, Ralph Stirling wrote:
Date: Mon, 11 Jan 2021 23:48:56 +0000
From: Ralph Stirling <ralph.stirl...@wallawalla.edu>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net>
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
I've made a bit of progress now. I found a Digilent HS2
jtag dongle, and got to the point of (apparently) successfully
loading an SPI bitstream to the 7I90 (chose 7i90_spi_svst4_8.bit).
Running:
$ mesaflash --device 7i90hd --addr /dev/spidev0.0 --spi --readhmid
gives me the same "no 7I90HD board found" error though. I tried
adding a pullup resistor to the SDO pin, without change, which
would seem to indicate the 7I90HD is actively driving it low.
Is there a very simple blinky bitstream I can try loading to
be sure the jtag loading is successful? The /INIT yellow led
flashes briefly, and /DONE red led does go on during the load
and goes off afterward.
Thanks again.
-- Ralph
Theres no blinky light test bitfile but if you load the sserial
remote bitfile 7i90_ssremote.bit, The init LED should light once
configured (well 50 ms after configured indicating a watchdog timeout)
________________________________________
From: Peter C. Wallace [p...@mesanet.com]
Sent: Friday, January 8, 2021 1:22 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
CAUTION: This email originated from outside the Walla Walla University email
system.
On Fri, 8 Jan 2021, Ralph Stirling wrote:
Date: Fri, 8 Jan 2021 21:08:55 +0000
From: Ralph Stirling <ralph.stirl...@wallawalla.edu>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net>
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
Not having Xilinx Impact tool on the Rpi (or anywhere
at the moment), I found a tutorial on setting up
OpenOCD for jtag on the Rpi. I have installed OpenOCD
on my RPi 3B+ and connected the gpio to the JTAG pins
on the 7i90HD, following this tutorial:
https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Fmovr0.com%2F2016%2F09%2F02%2Fuse-raspberry-pi-23-as-a-jtagswd-adapter%2F&data=04%7C01%7Cralph.stirling%40wallawalla.edu%7C0e816ca3cbad4d7d899008d8b41b9984%7Cd958f048e43142779c8debfb75e7aa64%7C0%7C0%7C637457377919675638%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=6NnpSk67I%2FpHEaLUmq1Fmg0%2FX6XH2KpNqNghMfBq6lk%3D&reserved=0
The last step seems to be to make a configuration
file for the target device. The EEPROMs are WInbond
25Q16JVNIQ as best I can read the chip labels. OpenOCD
doesn't have anything that looks directly applicable.
I also don't know where the two chips are in the jtag
chain.
You dont need to do this if you can program the FPGA
(and JTAG programming large EEPROMS is glacially slow)
If you can program the FPGA via JTAG, you program the FPGA with a SPI
configuration, and then run mesaflash from the RPI to write the
flash memory
Am I heading down a rat hole, or getting close to success?
Thanks again.
-- Ralph
________________________________________
From: Peter C. Wallace [p...@mesanet.com]
Sent: Thursday, January 7, 2021 3:47 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
CAUTION: This email originated from outside the Walla Walla University email
system.
On Thu, 7 Jan 2021, Ralph Stirling wrote:
Date: Thu, 7 Jan 2021 23:37:03 +0000
From: Ralph Stirling <ralph.stirl...@wallawalla.edu>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net>
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
I assumed that the 7i90hd would recognize SPI
directly, like the 7c81 does. Do I have to go
dig up a parallel port computer from somewhere
and get at least mesaflash running on it just
so I can get spi working for the pi? That is an
unfortunate hurdle. I don't see anything in the
manual about needing to load the correct bitstream
over parallel in order to use spi. In fact, I read
this in the manual:
Yep, you need to have SPI firmware loaded in the 7I90HD
default 7I90HD firmware is EPP, so a device with a EPP
interface is needed to load the SPI configuration
I would suggest loading the SPI interface into the
secondary flash leaving the primary as EPP for a fallback
That is, power the 7I90 with the flash jumper in the "P" position
them move the jumper to "S" before loadin the SPI firmware
"Linux and Windows utility programs mesaflash and mesaflash.exe are provided to
write configuration files to the 7I90HD EEPROM via the RS-422 interface and
LBP16. The
linux utility can also write configuration files via the EPP interface. These
files depend on
a simple SPI interface built into both the standard user FPGA bitfiles and the
fallback
bitfile."
Well there are 2 SPI interfaces, the HM2 compatible host interface (which needs
specific SPI firmware) and the SPI Flash memory interface (which is in HM2
memory space and allows access to the SPI flash chip)
I can tack on a pullup to SDO. I have put four
scope probes on the four signals, and see data
when interrogating the 7c81, but not the 7i90hd.
The clock from the pi is correct.
Thanks again.
-- Ralph
________________________________________
From: Peter C. Wallace [p...@mesanet.com]
Sent: Thursday, January 7, 2021 3:18 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
Looks right
2 layer should be fine as long as the ground is solid (wide)
between the 7I90 and the RPI (and lo longer than a couple of
inches
You might try adding a pullup to SDO (7I90 15) to see if you read
0xFFFFFFFF which would indicate the the 7I90 is not driving SDO
Sure you have a SPI config in the 7I90?
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.sourceforge.net%2Flists%2Flistinfo%2Femc-users&data=04%7C01%7Cralph.stirling%40wallawalla.edu%7C0e816ca3cbad4d7d899008d8b41b9984%7Cd958f048e43142779c8debfb75e7aa64%7C0%7C0%7C637457377919705615%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=e%2B0tbcvwCGF8x29dPXURO5XiQjISZkZVL2grIG4N5cw%3D&reserved=0
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.sourceforge.net%2Flists%2Flistinfo%2Femc-users&data=04%7C01%7Cralph.stirling%40wallawalla.edu%7C0e816ca3cbad4d7d899008d8b41b9984%7Cd958f048e43142779c8debfb75e7aa64%7C0%7C0%7C637457377919715613%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=qfzGt6erxaM5sonMllyUzVQSG6jjOVmGMCq6cneSSoE%3D&reserved=0
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.sourceforge.net%2Flists%2Flistinfo%2Femc-users&data=04%7C01%7Cralph.stirling%40wallawalla.edu%7C0e816ca3cbad4d7d899008d8b41b9984%7Cd958f048e43142779c8debfb75e7aa64%7C0%7C0%7C637457377919715613%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=qfzGt6erxaM5sonMllyUzVQSG6jjOVmGMCq6cneSSoE%3D&reserved=0
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.sourceforge.net%2Flists%2Flistinfo%2Femc-users&data=04%7C01%7Cralph.stirling%40wallawalla.edu%7C0e816ca3cbad4d7d899008d8b41b9984%7Cd958f048e43142779c8debfb75e7aa64%7C0%7C0%7C637457377919715613%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=qfzGt6erxaM5sonMllyUzVQSG6jjOVmGMCq6cneSSoE%3D&reserved=0
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.sourceforge.net%2Flists%2Flistinfo%2Femc-users&data=04%7C01%7Cralph.stirling%40wallawalla.edu%7C0e816ca3cbad4d7d899008d8b41b9984%7Cd958f048e43142779c8debfb75e7aa64%7C0%7C0%7C637457377919715613%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=qfzGt6erxaM5sonMllyUzVQSG6jjOVmGMCq6cneSSoE%3D&reserved=0
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
