Pheko, For the SSR it is not a roll over cable it is a straight thru.
What I used to use, was a couple of RJ-45 to DB9 kits that I wired with pin 1 on the RJ45 end to pin 1 on the DB-9, and pins 2 through 8 wired the same on both sides. You should be good to go from there. David -----Original Message----- From: Mamabolo, Pheko [mailto:[email protected]] Sent: Friday, August 14, 2009 11:02 AM To: Enterasys Customer Mailing List Subject: RE: [enterasys] Console management access assistance request. Not yet am going to try another Enterasys roll over cable over the weekend. -----Original Message----- From: Lou H. Goddard [mailto:[email protected]] Sent: Friday, August 14, 2009 4:39 PM To: Enterasys Customer Mailing List Subject: RE: [enterasys] Console management access assistance request. Did you make a new cable yet? ----- Original Message ----- From: "Mamabolo, Pheko" <[email protected]> Sent: Thu, 8/13/2009 11:17am To: Enterasys Customer Mailing List <[email protected]> Subject: RE: [enterasys] Console management access assistance request. Hi, Thanx for all the replies: I have tried diffent baud rate. Nothing appears on the CLI. Kind Regards, Pheko Mamabolo Network Systems Engineer Siemens IT Solutions and Services 300 Janadel Avenue Halfway House 1685 Main +27(0) 11 652 2000 Direct +27(0) 11 652 8170 Mobile +27(0) 82 487 9822 Fax: +27(0) 86 506 6018 E-mail: [email protected] www.siemens.co.za -----Original Message----- From: Dennis Roos [mailto:[email protected]] Sent: Thursday, August 13, 2009 3:15 PM To: Enterasys Customer Mailing List Subject: Re: [enterasys] Console management access assistance request. Holbrook, Dave wrote: <SNIP> > From: Mamabolo, Pheko [mailto:[email protected]] > Sent: Thursday, August 13, 2009 8:31 AM > To: Enterasys Customer Mailing List > Subject: [enterasys] Console management access assistance request. > > Hi > > We are battling to access 8600 SmartSwitch console management via COM port and via utp. > We have tried booting it with FLASH and without the FLASH. Please assist with guide to accessing this device via CLI. > Hate to sound a nuisance, but did you try different baudrate/stopbit/flowcontrol configurations ? Was there any output on the console (minicom/hyperterm/putty) ? --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected] ________________________________________________________________________ ________________ Disclaimer and Confidentiality Note This e-mail communication, its attachments, if any, and any rights attaching to it are, unless the context clearly indicates otherwise, the property of Siemens Limited. It is confidential, private and intended for the addressee only. If you are not the intended recipient and receive this communication in error, you are hereby notified that any review, copying, use, discloser or distribution in any manner whatsoever is strictly prohibited. Please notify the sender immediately that you have received this e-mail in error and delete the e-mail and any copies of it. Views and opinions expressed in this e-mail are those of the sender unless clearly stated as those of Siemens Limited. Siemens Limited accepts no liability for any loss or damage whatsoever, and howsoever incurred or suffered resulting or arising from the use of this e-mail communication and/or its attachments. Siemens Limited does not warrant the integrity of this e-mail communication nor that it is free of errors, viruses, interception or interference. For more information about Siemens Limited, visit our website at www.siemens.com --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected] ------------------ CONFIDENTIALITY NOTICE --------------- This message, including any attachments, is for the sole use of the intended recipient(s) and may contain privileged confidential information protected by law. Any unauthorized review, use, disclosure or distribution of this message is prohibited. If you are not the intended recipient, please contact the sender by reply e-mail and destroy all copies of this message. ------------------ CONFIDENTIALITY NOTICE --------------- -------- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected] ________________________________________________________________________ ________________ Disclaimer and Confidentiality Note This e-mail communication, its attachments, if any, and any rights attaching to it are, unless the context clearly indicates otherwise, the property of Siemens Limited. It is confidential, private and intended for the addressee only. If you are not the intended recipient and receive this communication in error, you are hereby notified that any review, copying, use, discloser or distribution in any manner whatsoever is strictly prohibited. Please notify the sender immediately that you have received this e-mail in error and delete the e-mail and any copies of it. Views and opinions expressed in this e-mail are those of the sender unless clearly stated as those of Siemens Limited. Siemens Limited accepts no liability for any loss or damage whatsoever, and howsoever incurred or suffered resulting or arising from the use of this e-mail communication and/or its attachments. Siemens Limited does not warrant the integrity of this e-mail communication nor that it is free of errors, viruses, interception or interference. For more information about Siemens Limited, visit our website at www.siemens.com --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected] --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected]
